Ford ST OEM-Style Gloss Black 10 Y-Spoke Forged Wheels
Monoblock · Gloss Black
2019 Ford Focus Wagon Vignale Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Focus Wagon Vignale wheels? This page gives the 2019 Ford Focus Wagon Vignale bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged Ford Focus Wagon Vignale rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ford Focus Wagon Vignale (2019): 5x108 bolt pattern, 63.4mm center bore. Factory wheels: 18x8.0J F/R. Reference fitment ranges.
Bolt Pattern5x108
Wheel Bolt/NutM12x1.5 Nut
Center Bore63.4mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2019
CategoryWagon
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8.0J F/R |
| Flush Fitment | 19x8.5J at ET42 offset |
| Maximum Aggressive | 19x9.0J at ET38 offset |
Forged Wheel Designs for the Ford Focus Wagon Vignale
Every design below is forged to order, so it can be machined to the Ford Focus Wagon Vignale's 5x108 bolt pattern and 63.4 mm center bore, with the width and offset calculated for your setup.
Ford OEM-Style Satin Black 3-Spoke Forged Wheels
Monoblock · Satin Black
Vossen HF4-T-Style Gloss Black 5 W-Spoke Forged Wheels
Replica · Gloss Black
Vossen Bronze Gold / Bronze 5 W-Spoke Forged Wheels
Replica · Bronze Gold / Bronze
Vossen Gray Directional Multi-Spoke Forged Wheels
Replica · Gray
Gloss White Slotted Dish Forged Wheels
Monoblock · Gloss White
Belak 5-Star Spoke Riveted Wide Lip Forged Drag Racing Wheels
Drag Racing · Custom Finish
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Wagons split the difference between sedan agility and load-carrying duty, and the wheels have to serve both roles. A forged wheel holds the same structural margin as the factory piece while trimming rotational weight, which benefits both the empty-car handling and the loaded-car ride.
The Ford Focus Wagon Vignale runs a 5x108 bolt pattern, 63.4mm center bore, and a 18x8.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET42, which tucks the tire under the fender lip on a stock-height Ford Focus Wagon Vignale. Our Maximum Aggressive reference is 19x9.0J ET38 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Focus Wagon Vignale OE Wheel Specs
The 2019 Ford Focus Wagon Vignale (Wagon) uses a 5x108 bolt pattern with a 63.4mm center bore. Factory wheels are 18x8.0J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Focus Wagon Vignale (2019) we drill the 5x108 pattern and cut the centre bore to 63.4mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 18x8.0J ET50 → ~6.47″ backspacing
- Flush: 19x8.5J ET42 → ~6.4″ backspacing
- Max: 19x9.0J ET38 → ~6.5″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Focus Wagon Vignale? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Focus Wagon Vignale use?
The 2019 Ford Focus Wagon Vignale uses a 5x108 bolt pattern.
How many lug bolts does the Ford Focus Wagon Vignale use?
The Ford Focus Wagon Vignale uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Focus Wagon Vignale?
The Ford Focus Wagon Vignale's center bore is 63.4mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Focus Wagon Vignale?
Factory wheels on the Ford Focus Wagon Vignale are 18x8.0J F/R.
What is the biggest wheel size I can fit on my Ford Focus Wagon Vignale without rubbing?
The most aggressive fitment we recommend without fender work is 19x9.0J at ET38 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Focus Wagon Vignale?
For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET42 offset as a starting point on a stock or mildly lowered Ford Focus Wagon Vignale.
Do I need wheel spacers for my Ford Focus Wagon Vignale?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Focus Wagon Vignale?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.4" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Focus Wagon Vignale?
The Ford Focus Wagon Vignale runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.