2025 Ford Explorer ST Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Explorer ST wheels? This page gives the 2025 Ford Explorer ST bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ford Explorer ST rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ford Explorer ST (2025): 5x114.3 bolt pattern, 70.5mm center bore. Factory wheels: 21x9.0J F/R. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/Nut1/2\"x20 Nut
Center Bore70.5mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Year2025
CategorySUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 21x9.0J F/R |
| Flush Fitment | 22x10.0J at ET35 offset |
| Maximum Aggressive | 22x10.5J at ET30 offset |
Forged Wheel Designs for the Ford Explorer ST
Every design below is forged to order, so it can be machined to the Ford Explorer ST's 5x114.3 bolt pattern and 70.5 mm center bore, with the width and offset calculated for your setup.
Vossen Transparent Gray 10-Spoke Forged Wheels
Replica · Transparent Gray
BBS-Style Bright Silver Y-Spoke Mesh Forged Wheels
Monoblock · Bright Silver
Weld Racing S71-Style Gloss Black 5-Spoke Deep Lip Forged Drag Racing Wheels
Drag Racing · Gloss Black
Gloss Black 10 Y-Spoke Forged Wheels
Monoblock · Gloss Black
Ford Mustang OEM-Style Chrome 6-Spoke Forged Wheels
Monoblock · Chrome
Platinum Bright Silver Mesh Deep Lip Forged Wheels
Deep Dish · Bright Silver
See all Ford Explorer wheel designs Ford OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Ford Explorer ST's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Ford Explorer ST runs a 5x114.3 bolt pattern, 70.5mm center bore, and a 21x9.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 22x10.0J ET35, which tucks the tire under the fender lip on a stock-height Ford Explorer ST. Our Maximum Aggressive reference is 22x10.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Explorer ST OE Wheel Specs
The 2025 Ford Explorer ST (SUV) uses a 5x114.3 bolt pattern with a 70.5mm center bore. Factory wheels are 21x9.0J F/R.
Why the factory spec works for most owners:
- Preserves the factory-tuned ride and steering feel
- A mainstream size for this segment, keeping tire choice wide and prices reasonable
- Leaves full clearance for the stock brakes and suspension hardware
- Keeps handling predictable and consistent in everyday conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Explorer ST (2025) we drill the 5x114.3 pattern and cut the centre bore to 70.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 21x9.0J ET45 → ~6.77″ backspacing
- Flush: 22x10.0J ET35 → ~6.88″ backspacing
- Max: 22x10.5J ET30 → ~6.93″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Explorer ST? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Explorer ST use?
The 2025 Ford Explorer ST uses a 5x114.3 bolt pattern.
How many lug bolts does the Ford Explorer ST use?
The Ford Explorer ST uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Explorer ST?
The Ford Explorer ST's center bore is 70.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Explorer ST?
Factory wheels on the Ford Explorer ST are 21x9.0J F/R.
What is the biggest wheel size I can fit on my Ford Explorer ST without rubbing?
The most aggressive fitment we recommend without fender work is 22x10.5J at ET30 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Explorer ST?
For a flush look with minimal to no rubbing, we recommend 22x10.0J at ET35 offset as a starting point on a stock or mildly lowered Ford Explorer ST.
Do I need wheel spacers for my Ford Explorer ST?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Explorer ST?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Explorer ST?
The Ford Explorer ST runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.