
BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold
Fitting Dacia Sandero Stepway (UK) wheels? This page gives the 2021 Dacia Sandero Stepway (UK) bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Dacia Sandero Stepway (UK) rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Dacia Sandero Stepway (UK) (2021): 4x100 bolt pattern, 60.1mm center bore. Factory wheels: 16x6.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x6.5J F/R |
| Flush Fitment | 17x7.0J at ET35 offset |
| Maximum Aggressive | 18x7.5J at ET32 offset |
Every design below is forged to order, so it can be machined to the Dacia Sandero Stepway (UK)'s 4x100 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.

2-Piece · Gold

Monoblock · Gold


Monoblock · Gloss White

Deep Dish · Gunmetal

Monoblock · Black Machined

Monoblock · Matte Bronze

Monoblock · Bright Silver
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


Because an SUV's center of gravity is already higher than a sedan's, anything added at the corners — including wheel weight — has an outsized effect on handling balance. A forged wheel lets us hit the visual stance owners want without adding the rotational mass a cast wheel of the same strength would carry.
The Dacia Sandero Stepway (UK) runs a 4x100 bolt pattern, 60.1mm center bore, and a 16x6.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x7.0J ET35, which tucks the tire under the fender lip on a stock-height Dacia Sandero Stepway (UK). Our Maximum Aggressive reference is 18x7.5J ET32 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2021 Dacia Sandero Stepway (UK) (Crossover) uses a 4x100 bolt pattern with a 60.1mm center bore. Factory wheels are 16x6.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Dacia Sandero Stepway (UK) (2021) we drill the 4x100 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Dacia spec, or want a wheel built to a custom offset for your Dacia Sandero Stepway (UK)? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.