← Fitment Guide · All Citroen Fitment Guides

2008 Citroen C5 Estate Wheels & Rims: Bolt Pattern, Offset & Sizes

Fitting Citroen C5 Estate wheels? This page gives the 2008 Citroen C5 Estate bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged Citroen C5 Estate rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.

Citroen C5 Estate (2008): 5x108 bolt pattern, 65.1mm center bore. Factory wheels: 17x7.0J F/R. Reference fitment ranges.

Bolt Pattern5x108

Wheel Bolt/NutM12x1.25 Bolt

Center Bore65.1mm

Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)

Year2008

CategoryWagon

✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →

Wheel Size & Offset at a Glance

Citroen C5 Estate wheel size and offset comparison by configuration
Configuration	Wheel Size & Offset
Factory (OE)	17x7.0J F/R
Flush Fitment	19x8.5J at ET25 offset
Maximum Aggressive	20x9.0J at ET22 offset

How to Read Wheel Offset & Measurements

Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.

Diagram showing wheel measurement points: centerline, center bore diameter, PCD, offset, rim width and diameter — Centerline, center bore, PCD, offset, width & diameter

Diagram comparing positive, zero, and negative wheel offset relative to the wheel centerline — Positive vs. zero vs. negative offset

ANKUSI Engineering Expert Advice

A wagon carries wagon-specific weight distribution — more mass over the rear axle when loaded — so wheel strength at the rear corners matters as much as the front. Forging lets us match the factory's strength target on both ends while keeping rotational mass down, which keeps the ride composed whether the cargo area is empty or full.

The Citroen C5 Estate runs a 5x108 bolt pattern, 65.1mm center bore, and a 17x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET25, which tucks the tire under the fender lip on a stock-height Citroen C5 Estate. Our Maximum Aggressive reference is 20x9.0J ET22 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.

Citroen C5 Estate OE Wheel Specs

The 2008 Citroen C5 Estate (Wagon) uses a 5x108 bolt pattern with a 65.1mm center bore. Factory wheels are 17x7.0J F/R.

Why the factory spec works for most owners:

Balances ride comfort with everyday drivability
A commonly used size for this vehicle class, supporting parts and tire availability
Maintains clearance for the factory suspension and brake components
Provides stable, predictable handling across normal driving conditions

ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Citroen C5 Estate (2008) we drill the 5x108 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.

IATF 16949 & ISO 9001 certified · own 10,000-ton press in Guangzhou · from a single set to a full container

Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.

The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.

Get a quote for this car WhatsApp the factory

Flush Fitment

For a flush look with minimal rubbing, F/R 19x8.5J ET25 is the recommended starting point on a stock or mildly lowered Citroen C5 Estate.

Maximum Aggressive Fitment

F/R 20x9.0J ET22 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.

5-Tier Configuration Options

A Factory-Style 17x7.0J ET32

Recommended setup: 17x7.0J ET32 | Economy impact: Negligible | Best for: Daily commuting, family use

Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆

Estimated cost: $450-800 (wheels + tires + install)

B Comfortable Upgrade 19x8.0J ET29

Recommended setup: 19x8.0J ET29 | Economy impact: -2 to -4% | Best for: Daily / street

Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆

Estimated cost: $1,950-2,550 (wheels + tires + install)

C Balanced / Flush Fit 19x8.5J ET25

Recommended setup: 19x8.5J ET25 | Economy impact: -4 to -6% | Best for: Street

Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆

Estimated cost: $2,600-3,400 (wheels + tires + install)

D Aggressive 20x9.0J ET24

Recommended setup: 20x9.0J ET24 | Economy impact: -6 to -9% | Best for: Show / occasional track

Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆

Estimated cost: $3,900-5,000 (wheels + tires + install)

E Max Aggressive 20x9.0J ET22

Recommended setup: 20x9.0J ET22 | Economy impact: -8 to -12% | Best for: Show only

Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆

Estimated cost: $4,800-6,200+ (wheels + tires + install)

Performance Comparison Matrix

Metric	Tier A	Tier B	Tier C	Tier D	Tier E
Wheel Spec	17x7.0J ET32	19x8.0J ET29	19x8.5J ET25	20x9.0J ET24	20x9.0J ET22
Economy Impact	Negligible	-2 to -4%	-4 to -6%	-6 to -9%	-8 to -12%
Appearance	7/10	8/10	8.5/10	9/10	9.5/10
Comfort	9.5/10	9/10	8/10	6.5/10	4/10
Install Difficulty	★☆☆☆☆	★☆☆☆☆	★★☆☆☆	★★★☆☆	★★★★☆
Cost Range	$450-800	$1,950-2,550	$2,600-3,400	$3,900-5,000	$4,800-6,200+
Best For	Daily commuting, family use	Daily / street	Street	Show / occasional track	Show only

Real-World Reference Cases

The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.

Case 1: Daily Driver (Factory-Style)

Profile: Everyday driving, prioritizes comfort and low running cost.

Setup: 17x7.0J ET32

Cost: ~$620

Outcome: Minimal visual change, ride and fuel economy essentially unaffected.

Case 2: Balanced Enthusiast (Balanced / Flush Fit)

Profile: Wants a sportier stance without sacrificing daily usability.

Setup: 19x8.5J ET25

Cost: ~$3,000

Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.

Case 3: Show Build (Max Aggressive)

Profile: Built primarily for shows or occasional track/show use.

Setup: 20x9.0J ET22

Cost: ~$5,500

Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.

Decision Guide

What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.

What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.

How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.

Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Citroen C5 Estate owners.

Offset & Backspacing Reference

Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):

OE: 17x7.0J ET32 → ~5.26″ backspacing
Flush: 19x8.5J ET25 → ~5.73″ backspacing
Max: 20x9.0J ET22 → ~5.87″ backspacing

Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Citroen spec, or want a wheel built to a custom offset for your Citroen C5 Estate? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.

Custom Forged Wheels for the Citroen C5 Estate (2008)

Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.

Every set is cut to order, so the 5x108 pattern and the 65.1mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Citroen orders on this platform land somewhere between the 19x8.5J ET25 flush setup and the 20x9.0J ET22 aggressive setup referenced above.

Designs we already tool for the 5x108 pattern — each one is re-cut to your sizes and offsets:

Citroen C5 / Peugeot 508 Forged Wheels – Gloss Black / Gunmetal Machined Face

Citroen C5 / Peugeot 508 Forged Wheels – Gloss White 10-Spoke

Citroen C5 / Peugeot 508 Forged Wheels – Gloss Black 5 Y-Spoke

Citroen C5 / Peugeot 508 Forged Wheels – Bright Silver Custom

Request a quote WhatsApp the factory Wholesale & OEM

Frequently Asked Questions

What bolt pattern (PCD) does the Citroen C5 Estate use?

The 2008 Citroen C5 Estate uses a 5x108 bolt pattern.

How many lug bolts does the Citroen C5 Estate use?

The Citroen C5 Estate uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.

What is the center bore size on the Citroen C5 Estate?

The Citroen C5 Estate's center bore is 65.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.

What size are the factory (stock) wheels on the Citroen C5 Estate?

Factory wheels on the Citroen C5 Estate are 17x7.0J F/R.

What is the biggest wheel size I can fit on my Citroen C5 Estate without rubbing?

The most aggressive fitment we recommend without fender work is 20x9.0J at ET22 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.

What does a flush wheel fitment look like on the Citroen C5 Estate?

For a flush look with minimal to no rubbing, we recommend 19x8.5J at ET25 offset as a starting point on a stock or mildly lowered Citroen C5 Estate.

Do I need wheel spacers for my Citroen C5 Estate?

No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.

How do I calculate wheel backspacing for my Citroen C5 Estate?

Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.73" of backspacing.

What's the difference between wheel offset and backspacing?

Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.

Can I run staggered wheels (different sizes front and rear) on my Citroen C5 Estate?

The Citroen C5 Estate runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.

Forged Wheel Designs for the Citroen C5 Estate

Every design below is forged to order, so it can be machined to the Citroen C5 Estate's 5x108 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.