
Citroen OEM-Style Matte Black 10-Spoke Forged Wheels
Monoblock · Matte Black
Fitting Citroen C4 notchback wheels? This page gives the 2008 Citroen C4 notchback bolt pattern (4x108), centre bore, factory rim size and the offset range for aftermarket and forged Citroen C4 notchback rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Citroen C4 — styles, sizes & factory quote →
Citroen C4 notchback (2008): 4x108 bolt pattern, 65.1mm center bore. Factory wheels: 16x6.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x6.5J F/R |
| Flush Fitment | 17x7.5J at ET20 offset |
| Maximum Aggressive | 18x8.0J at ET18 offset |
Every design below is forged to order, so it can be machined to the Citroen C4 notchback's 4x108 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Matte Black

Monoblock · Bronze Gold

Monoblock · Gloss White

Deep Dish · Gunmetal

Monoblock · Black Machined

Monoblock · Matte Bronze

Monoblock · Matte Silver

Monoblock · Silver
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Citroen C4 notchback runs a 4x108 bolt pattern, 65.1mm center bore, and a 16x6.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x7.5J ET20, which tucks the tire under the fender lip on a stock-height Citroen C4 notchback. Our Maximum Aggressive reference is 18x8.0J ET18 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2008 Citroen C4 notchback (Sedan) uses a 4x108 bolt pattern with a 65.1mm center bore. Factory wheels are 16x6.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Citroen C4 notchback (2008) we drill the 4x108 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Citroen spec, or want a wheel built to a custom offset for your Citroen C4 notchback? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.