
Citroen OEM-Style Matte Black 10-Spoke Forged Wheels
Monoblock · Matte Black
Fitting Citroen C4 Coupe with Panoramic Sunroof wheels? This page gives the 2005 Citroen C4 Coupe with Panoramic Sunroof bolt pattern (4x108), centre bore, factory rim size and the offset range for aftermarket and forged Citroen C4 Coupe with Panoramic Sunroof rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Forged wheels for Citroen C4 — styles, sizes & factory quote →
Citroen C4 Coupe with Panoramic Sunroof (2005): 4x108 bolt pattern, 65.1mm center bore. Factory wheels: 17x6.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 17x6.5J F/R |
| Flush Fitment | 18x8.0J at ET20 offset |
| Maximum Aggressive | 18x8.5J at ET15 offset |
Every design below is forged to order, so it can be machined to the Citroen C4 Coupe with Panoramic Sunroof's 4x108 bolt pattern and 65.1 mm center bore, with the width and offset calculated for your setup.

Monoblock · Matte Black

Monoblock · Silver

Monoblock · Bright Silver

Monoblock · Black Machined

Monoblock · Matte Bronze

Monoblock · Matte Silver

Deep Dish · Gunmetal

Monoblock · Bronze Gold
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


The Citroen C4 Coupe with Panoramic Sunroof's chassis tuning assumes a certain amount of rotational mass at each corner. Forging lets ANKUSI cut that mass while matching the factory strength rating, which sharpens turn-in and reduces the energy the brakes have to absorb — a real gain on a coupe platform, not just a styling change.
The Citroen C4 Coupe with Panoramic Sunroof runs a 4x108 bolt pattern, 65.1mm center bore, and a 17x6.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 18x8.0J ET20, which tucks the tire under the fender lip on a stock-height Citroen C4 Coupe with Panoramic Sunroof. Our Maximum Aggressive reference is 18x8.5J ET15 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2005 Citroen C4 Coupe with Panoramic Sunroof (Coupe) uses a 4x108 bolt pattern with a 65.1mm center bore. Factory wheels are 17x6.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Citroen C4 Coupe with Panoramic Sunroof (2005) we drill the 4x108 pattern and cut the centre bore to 65.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Citroen spec, or want a wheel built to a custom offset for your Citroen C4 Coupe with Panoramic Sunroof? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.