Bentley Continental / Flying Spur Forged Wheels
Gloss Black Directional Milled
2022 Bentley Flying Spur Hybrid Odyssean Edition Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Bentley Flying Spur Hybrid Odyssean Edition wheels? This page gives the 2022 Bentley Flying Spur Hybrid Odyssean Edition bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Bentley Flying Spur Hybrid Odyssean Edition rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Bentley Flying Spur Hybrid Odyssean Edition (2022): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 21x9.0J R: 21x10.5J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Caliper TypeBrembo multi-piston fixed caliper, front & rear (OEM, standard across Bentley Continental/Flying Spur lineup)
Year2022
CategoryHybrid Sedan
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 21x9.0J R: 21x10.5J |
| Flush Fitment | F 22x10.0J ET30 / R 22x11.5J ET35 |
| Maximum Aggressive | F 23x10.5J ET25 / R 23x12.0J ET30 |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Bentley Flying Spur Hybrid Odyssean Edition runs a 5x130 bolt pattern, 71.6mm center bore, and a F: 21x9.0J wheel from the factory. Our Flush Fitment reference is F 22x10.0J ET30 / R 22x11.5J ET35, which tucks the tire under the fender lip on a stock-height Bentley Flying Spur Hybrid Odyssean Edition. Our Maximum Aggressive reference is F 23x10.5J ET25 / R 23x12.0J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Bentley Flying Spur Hybrid Odyssean Edition OE Wheel Specs
The 2022 Bentley Flying Spur Hybrid Odyssean Edition (Hybrid Sedan) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 21x9.0J R: 21x10.5J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Bentley Flying Spur Hybrid Odyssean Edition (2022) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, F 22x10.0J ET30 / R 22x11.5J ET35 is the recommended starting point on a stock or mildly lowered Bentley Flying Spur Hybrid Odyssean Edition.
Maximum Aggressive Fitment
F 23x10.5J ET25 / R 23x12.0J ET30 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style F 21x9.0J ET35 / R 21x10.5J ET40
Recommended setup: F 21x9.0J ET35 / R 21x10.5J ET40 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade F 22x9.5J ET33 / R 22x11.0J ET38
Recommended setup: F 22x9.5J ET33 / R 22x11.0J ET38 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit F 22x10.0J ET30 / R 22x11.5J ET35
Recommended setup: F 22x10.0J ET30 / R 22x11.5J ET35 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive F 23x10.5J ET28 / R 23x12.0J ET33
Recommended setup: F 23x10.5J ET28 / R 23x12.0J ET33 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive F 23x10.5J ET25 / R 23x12.0J ET30
Recommended setup: F 23x10.5J ET25 / R 23x12.0J ET30 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | F 21x9.0J ET35 / R 21x10.5J ET40 | F 22x9.5J ET33 / R 22x11.0J ET38 | F 22x10.0J ET30 / R 22x11.5J ET35 | F 23x10.5J ET28 / R 23x12.0J ET33 | F 23x10.5J ET25 / R 23x12.0J ET30 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: F 21x9.0J ET35 / R 21x10.5J ET40
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: F 22x10.0J ET30 / R 22x11.5J ET35
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: F 23x10.5J ET25 / R 23x12.0J ET30
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
1
What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.
2
What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.
3
How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.
4
Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Bentley Flying Spur Hybrid Odyssean Edition owners.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 21x9.0J ET35 → ~6.38″ F backspacing, R 21x10.5J ET40 → ~7.32″ R backspacing
- Flush: F 22x10.0J ET30 → ~6.68″ F backspacing, R 22x11.5J ET35 → ~7.63″ R backspacing
- Max: F 23x10.5J ET25 → ~6.73″ F backspacing, R 23x12.0J ET30 → ~7.68″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Bentley spec, or want a wheel built to a custom offset for your Bentley Flying Spur Hybrid Odyssean Edition? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the Bentley Flying Spur Hybrid Odyssean Edition (2022)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x130 pattern and the 71.6mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose.
Designs we already tool for the 5x130 pattern — each one is re-cut to your sizes and offsets:
Bentley OEM-Style Gloss Black Full-Face Forged Wheels – Bentley Bentayga / Flying Spur Fitment (5-Lug)
Bentley Continental GT / Bentayga Forged Wheels – Gloss Black Petal-Spoke Machined Face
Bentley Continental / Flying Spur Forged Wheels – Gloss Black Full-Face
Bentley Continental GT / Bentayga Forged Wheels – Silver 15-SpokeFrequently Asked Questions
What bolt pattern (PCD) does the Bentley Flying Spur Hybrid Odyssean Edition use?
The 2022 Bentley Flying Spur Hybrid Odyssean Edition uses a 5x130 bolt pattern.
How many lug bolts does the Bentley Flying Spur Hybrid Odyssean Edition use?
The Bentley Flying Spur Hybrid Odyssean Edition uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Bentley Flying Spur Hybrid Odyssean Edition?
The Bentley Flying Spur Hybrid Odyssean Edition's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Bentley Flying Spur Hybrid Odyssean Edition?
Factory wheels on the Bentley Flying Spur Hybrid Odyssean Edition are F: 21x9.0J R: 21x10.5J.
What is the biggest wheel size I can fit on my Bentley Flying Spur Hybrid Odyssean Edition without rubbing?
The most aggressive fitment we recommend without fender work is F 23x10.5J ET25 / R 23x12.0J ET30. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Bentley Flying Spur Hybrid Odyssean Edition?
For a flush look with minimal to no rubbing, we recommend F 22x10.0J ET30 / R 22x11.5J ET35 as a starting point on a stock or mildly lowered Bentley Flying Spur Hybrid Odyssean Edition.
Do I need wheel spacers for my Bentley Flying Spur Hybrid Odyssean Edition?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Bentley Flying Spur Hybrid Odyssean Edition?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.68" backspacing up front and 7.63" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Bentley Flying Spur Hybrid Odyssean Edition?
Yes — the Bentley Flying Spur Hybrid Odyssean Edition's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Forged Wheel Designs for the Bentley Flying Spur Hybrid Odyssean Edition
Every design below is forged to order, so it can be machined to the Bentley Flying Spur Hybrid Odyssean Edition's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Bentley Continental / Flying Spur Forged Wheels
Gloss Black 10-Spoke
Bentley Continental GT / Bentayga Forged Wheels
Matte Silver Full-Face Machined Face
Bentley Continental / Flying Spur Forged Wheels
Gloss Black Full-Face
Bentley Continental GT / Bentayga Forged Wheels
Silver 15-Spoke
Bentley Continental GT / Bentayga Forged Wheels
Gloss Black Petal-Spoke Machined Face
Bentley OEM-Style Gloss Black Full-Face Forged Wheels
Bentley Bentayga / Flying Spur Fitment · 5-Lug
Bentley OEM-Style Gloss Black 5 V-Spoke Forged Wheels
Bentley Continental GT / Flying Spur Fitment · 5-Lug