Ford OEM-Style Satin Black 3-Spoke Forged Wheels
Monoblock · Satin Black
2010 Ford Focus ECOnetic Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Focus ECOnetic wheels? This page gives the 2010 Ford Focus ECOnetic bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged Ford Focus ECOnetic rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2010 Ford Focus ECOnetic uses a 5x108 bolt pattern with a 63.4 mm centre bore and M12x1.5 lug nuts. Factory wheels: 15x6J ET52.5. For aftermarket wheels, 16x7J ET40 sits flush.
Forged wheels for the 2010 Ford Focus ECOnetic — drilled 5x108 with a 63.4 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Ford Focus ECOnetic (2010): 5x108 bolt pattern, 63.4mm center bore, OE 15x6J ET52.5. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x108
Wheel Bolt/NutM12x1.5 Nut
Center Bore63.4mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2010
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 15x6J ET52.5 |
| Flush Fitment | 16x7J at ET40 offset |
Forged Wheel Designs for the Ford Focus ECOnetic
Every design below is forged to order, so it can be machined to the Ford Focus ECOnetic's 5x108 bolt pattern and 63.4 mm center bore, with the width and offset calculated for your setup.
Ford ST OEM-Style Gloss Black 10 Y-Spoke Forged Wheels
Monoblock · Gloss Black
Ford OEM-Style Chrome Mesh Polished Deep Lip Forged Wheels
Deep Dish · Chrome
Ford Mustang OEM-Style Light Gunmetal / Gray 5 Y-Spoke Forged Wheels
Monoblock · Light Gunmetal / Gray
Vossen HF-9-Style Gloss Black Full-Face Bi-Directional Milled Forged Wheels
Replica · Gloss Black
Weld Racing-Style Gloss Black / Silver Wide Lip Forged Drag Racing Wheels
Drag Racing · Gloss Black / Silver
Platinum Gloss Black 5 Y-Spoke Cut-Out Forged Wheels
Monoblock · Gloss Black
A Forged-Style Gunmetal / Polished Mesh Beadlock Forged Wheels
Off-Road Beadlock · Gunmetal / Polished
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Ford Focus ECOnetic ships from the factory on a 5x108 bolt pattern with a 63.4mm center bore and a 15x6J ET52.5 wheel. Our flush reference for the Ford Focus ECOnetic is 16x7J ET40.; our maximum aggressive reference is 17x7.5J ET35. — beyond that, expect clearance issues against the fender liner without further modification.
Ford Focus ECOnetic OE Wheel Specs
The Ford Focus ECOnetic ships from the factory on 5x108 bolt pattern wheels with a 63.4mm center bore. The stock wheel size is 15x6J ET52.5, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Focus ECOnetic (2010) we drill the 5x108 pattern and cut the centre bore to 63.4mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 15x6J | ET52.5 | 5.57 in (141 mm) | — | — |
| Flush | 16x7J | ET40 | 5.57 in (142 mm) | 0 mm | +25 mm |
| Maximum | 17x7.5J | ET35 | 5.63 in (143 mm) | +2 mm | +37 mm |
Vehicles With the Same Hub as the Ford Focus ECOnetic (5x108, 63.4 mm Bore)
In our database, 278 other vehicle entries from 17 makes use exactly the same 5x108 bolt pattern and 63.4 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x108 is used by 7.7% of the vehicle pages in our English fitment guide (499 of 6,503); 55.9% of those also use a 63.4 mm center bore.
Hub-Centric Rings for a 63.4 mm Center Bore
A wheel with a center bore larger than 63.4 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 64.1 mm | 64.1 → 63.4 mm |
| 65.1 mm | 65.1 → 63.4 mm |
| 66.1 mm | 66.1 → 63.4 mm |
| 66.6 mm | 66.6 → 63.4 mm |
| 73.1 mm | 73.1 → 63.4 mm |
ANKUSI forged wheels are bored to exactly 63.4 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Focus ECOnetic use?
The 2010 Ford Focus ECOnetic uses a 5x108 bolt pattern.
How many lug bolts does the Ford Focus ECOnetic use?
The Ford Focus ECOnetic uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Focus ECOnetic?
The Ford Focus ECOnetic's center bore is 63.4mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Focus ECOnetic?
Factory wheels on the Ford Focus ECOnetic are 15x6J ET52.5.
What does a flush wheel fitment look like on the Ford Focus ECOnetic?
For a flush look with minimal to no rubbing, we recommend 16x7J at ET40 offset as a starting point on a stock or mildly lowered Ford Focus ECOnetic.
Do I need wheel spacers for my Ford Focus ECOnetic?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Focus ECOnetic?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.57" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Focus ECOnetic?
The Ford Focus ECOnetic runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 15x6 wheels · 15 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.