Porsche 911 / M3 Forged Wheels
Matte Black Snowflake Multi-Spoke · 5-Lug
2005 Mahindra Scorpio Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Mahindra Scorpio wheels? This page gives the 2005 Mahindra Scorpio bolt pattern (5x160), centre bore, factory rim size and the offset range for aftermarket and forged Mahindra Scorpio rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Mahindra Scorpio (2005): 5x160 bolt pattern, 108mm center bore. Factory wheels: 15x6.5J F/R. Flush and max fitment confirmed on request.
Bolt Pattern5x160
Wheel Bolt/NutNut
Center Bore108mm
Wheel Load Rating900–1250 kg/wheel (SUV segment reference)
Caliper TypeFactory disc brakes, all four corners (OEM)
Year2005
CategorySUV
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Built to order by ANKUSI — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Forged wheels for the Mahindra ScorpioMachined to the 5x160 bolt pattern and 108 mm bore · 14–24 inch · offset calculated for your car · 3D drawing before production
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a vehicle this heavy, the wheel is a structural part before it is a styling part - it carries the load, the brake heat and the cornering forces all at once. A forged wheel buys back unsprung weight without giving up the load rating an SUV actually needs, which is the one number most cast aftermarket wheels quietly fall short on.
We publish the factory specification for the Mahindra Scorpio below. We have not yet been able to verify aftermarket flush or maximum-aggressive offsets for this exact variant against a source we trust, so we are not listing any - an invented offset is worse than no offset when a wheel has to clear a caliper.
Mahindra Scorpio OE Wheel Specs
The 2005 Mahindra Scorpio (SUV) uses a 5x160 bolt pattern with a 108mm center bore. Factory wheels are 15x6.5J F/R.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Mahindra Scorpio (2005) we drill the 5x160 pattern and cut the centre bore to 108mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Aftermarket Fitment: Confirmed on Request
Published aftermarket fitment for this exact variant is still thin, so we have not committed to a flush or maximum-aggressive figure. Our engineering team is still collecting verified data for this variant. In the meantime the factory specification above is accurate and is the safe reference point for ordering.
What we do know: Generation 2002 .. 2020, model years 2005-2020. Verified against two independent fitment references.
Need a wheel for this car now? Contact ANKUSI with your target diameter, width and offset and our engineers will confirm the correct forged spec against your brake package before anything is cut. You can also use our Offset & Backspacing Calculator to work through the numbers yourself.
Custom Forged Wheels for the Mahindra Scorpio (2005)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x160 pattern and the 108mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose.
We do not hold 5x160 wheels on a shelf — they are forged to order, which is why any offset, width and bore combination on this page is buildable rather than limited to a stock list.
Frequently Asked Questions
What bolt pattern (PCD) does the Mahindra Scorpio use?
The 2005 Mahindra Scorpio uses a 5x160 bolt pattern.
How many lug bolts does the Mahindra Scorpio use?
The Mahindra Scorpio uses a 5-lug bolt pattern (5x160), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Mahindra Scorpio?
The Mahindra Scorpio's center bore is 108mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Mahindra Scorpio?
Factory wheels on the Mahindra Scorpio are 15x6.5J F/R.
Do I need wheel spacers for my Mahindra Scorpio?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Mahindra Scorpio?
The Mahindra Scorpio runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Vehicles With the Same Hub as the Mahindra Scorpio (5x160, 108 mm Bore)
No other make in our database pairs 5x160 with a 108 mm center bore, so wheels taken from other brands need a hub-centric ring or a custom bore.
5x160 is used by <0.1% of the vehicle entries in our database (4 of 6,503); 25.0% of those also use a 108 mm center bore.
Mahindra Scorpio: Specs by Model Year
| Year | Bolt pattern | Center bore | Factory wheel |
|---|---|---|---|
| 2005 | 5x160 | 108 mm | 15x6.5J |
| 2020 | 5x160 | 108 mm | 15x6.5J |
Bolt pattern and center bore stay the same across all 2 model years in our database (2005–2020).
Hub-Centric Rings for a 108 mm Center Bore
A wheel with a center bore larger than 108 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 108.1 mm | 108.1 → 108 mm |
| 110.1 mm | 110.1 → 108 mm |
| 130.1 mm | 130.1 → 108 mm |
ANKUSI forged wheels are bored to exactly 108 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 15x6.5 wheels · 15 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
Forged Wheel Designs for the Mahindra Scorpio
Every design below is forged to order, so it can be machined to the Mahindra Scorpio's 5x160 bolt pattern and 108 mm center bore, with the width and offset calculated for your setup.
Wheelforce-Style Brushed Silver 10 Directional-Spoke Forged Wheels
Audi RS3 / BMW M3 G80 Fitment · 5-Lug
IM L7 / LS7 Forged Wheels
Black / Machined Directional Milled Machined Face
BMW M2 G87 / M3 G80 Forged Wheels
Bright Silver 5 Y-Spoke
Zauher-Style Brushed 5-Spoke Dish 2-Piece Riveted Forged Wheels
Porsche 911 / RS5 Fitment · 5-Lug
Porsche 911 / Panamera Forged Wheels
Gloss Black Mesh
Porsche 911 / BMW M3 Forged Wheels
Beige / Black Two-Tone 5-Spoke
Wheelforce-Style Matte Olive Directional Multi-Spoke Forged Wheels
Porsche 911 / M3 Fitment · 5-Lug
Bolt pattern and center bore on this page were cross-checked against at least two independent sources before publication. Last reviewed 2026-10-10. Spotted an error? Email info@ankusi.com and we will verify and correct it.