HRE P201-Style Gloss Black Petal Forged Wheels
Replica · Gloss Black
2001 Ferrari 360 Modena Challenge Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ferrari 360 Modena Challenge wheels? This page gives the 2001 Ferrari 360 Modena Challenge bolt pattern (5x108), centre bore, factory rim size and the offset range for aftermarket and forged Ferrari 360 Modena Challenge rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ferrari 360 Modena Challenge (2001): 5x108 bolt pattern, 67.1mm center bore. Factory wheels: F: 18x8.0J R: 10.5J. Reference fitment ranges.
Bolt Pattern5x108
Wheel Bolt/NutM14x1.5 Bolt
Center Bore67.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Caliper TypeBrembo fixed multi-piston aluminum monoblock caliper (OEM, standard across Ferrari lineup)
Year2001
CategoryRacecar
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 18x8.0J R: 10.5J |
| Flush Fitment | F 18x9.0J ET25 / R 18x11.5J ET32 |
| Maximum Aggressive | F 19x9.0J ET22 / R 19x12.0J ET28 |
Forged Wheel Designs for the Ferrari 360 Modena Challenge
Every design below is forged to order, so it can be machined to the Ferrari 360 Modena Challenge's 5x108 bolt pattern and 67.1 mm center bore, with the width and offset calculated for your setup.
Gold 5 Y-Spoke Forged Wheels
Monoblock · Gold
Ferrari OEM-Style Gloss Black 5 Twin-Spoke Star Side-Milled Forged Wheels
Replica · Gloss Black
Ferrari OEM-Style Gloss Black 5 Y-Spoke Forged Wheels
Monoblock · Gloss Black
HRE P200-Style Gloss Black 10 Y-Spoke Forged Wheels
Replica · Gloss Black
Gloss Black 10-Spoke Forged Wheels
Monoblock · Gloss Black
Vossen-Style Metallic Gray 10 Y-Spoke Forged Wheels
Monoblock · Metallic Gray
Ferrari OEM-Style Gloss Black Custom Forged Wheels
Monoblock · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Ferrari 360 Modena Challenge runs a 5x108 bolt pattern, 67.1mm center bore, and a F: 18x8.0J wheel from the factory. Our Flush Fitment reference is F 18x9.0J ET25 / R 18x11.5J ET32, which tucks the tire under the fender lip on a stock-height Ferrari 360 Modena Challenge. Our Maximum Aggressive reference is F 19x9.0J ET22 / R 19x12.0J ET28 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ferrari 360 Modena Challenge OE Wheel Specs
The 2001 Ferrari 360 Modena Challenge (Racecar) uses a 5x108 bolt pattern with a 67.1mm center bore. Factory wheels are F: 18x8.0J R: 10.5J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ferrari 360 Modena Challenge (2001) we drill the 5x108 pattern and cut the centre bore to 67.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F F: 18x8.0J R: 10.5J ET31.5 → ~5.74″ F backspacing, R F: 18x8.0J R: 10.5J ET39 → ~6.04″ R backspacing
- Flush: F 18x9.0J ET25 → ~5.98″ F backspacing, R 18x11.5J ET32 → ~7.51″ R backspacing
- Max: F 19x9.0J ET22 → ~5.87″ F backspacing, R 19x12.0J ET28 → ~7.6″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ferrari spec, or want a wheel built to a custom offset for your Ferrari 360 Modena Challenge? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ferrari 360 Modena Challenge use?
The 2001 Ferrari 360 Modena Challenge uses a 5x108 bolt pattern.
How many lug bolts does the Ferrari 360 Modena Challenge use?
The Ferrari 360 Modena Challenge uses a 5-lug bolt pattern (5x108), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ferrari 360 Modena Challenge?
The Ferrari 360 Modena Challenge's center bore is 67.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ferrari 360 Modena Challenge?
Factory wheels on the Ferrari 360 Modena Challenge are F: 18x8.0J R: 10.5J.
What is the biggest wheel size I can fit on my Ferrari 360 Modena Challenge without rubbing?
The most aggressive fitment we recommend without fender work is F 19x9.0J ET22 / R 19x12.0J ET28. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ferrari 360 Modena Challenge?
For a flush look with minimal to no rubbing, we recommend F 18x9.0J ET25 / R 18x11.5J ET32 as a starting point on a stock or mildly lowered Ferrari 360 Modena Challenge.
Do I need wheel spacers for my Ferrari 360 Modena Challenge?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ferrari 360 Modena Challenge?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.98" backspacing up front and 7.51" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ferrari 360 Modena Challenge?
Yes — the Ferrari 360 Modena Challenge's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.