Brabus-Style Gloss Black Carbon-Ring 10-Spoke Red Pinstripe Forged Wheels
Monoblock · Gloss Black
2008 Brabus Bullit Black Arrow Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Brabus Bullit Black Arrow wheels? This page gives the 2008 Brabus Bullit Black Arrow bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Brabus Bullit Black Arrow rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2008 Brabus Bullit Black Arrow uses a 5x112 bolt pattern with a 66.6 mm centre bore and M14x1.5 lug bolts. Factory wheels: F: 19x9.5J R: 19x10.5J. For aftermarket wheels, 20x10.0J ET30 front / 20x11.0J ET35 rear sits flush and 20x10.5J ET25 front / 20x11.5J ET30 rear is the most aggressive fit.
Forged wheels for the 2008 Brabus Bullit Black Arrow — drilled 5x112 with a 66.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Brabus Bullit Black Arrow (2008): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: F: 19x9.5J R: 19x10.5J. Reference fitment ranges.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore66.6mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2008
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 19x9.5J R: 19x10.5J |
| Flush Fitment | F 20x10.0J ET30 / R 20x11.0J ET35 |
| Maximum Aggressive | F 20x10.5J ET25 / R 20x11.5J ET30 |
Forged Wheel Designs for the Brabus Bullit Black Arrow
Every design below is forged to order, so it can be machined to the Brabus Bullit Black Arrow's 5x112 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.
Hamann-Style Silver Forged Wheels
Monoblock · Silver
Metallic Gray 2-Piece 5-Star Spoke Deep Lip Forged Wheels
2-Piece · Metallic Gray
Custom Finish 5 Y-Spoke Polished Forged Wheels
Monoblock · Custom Finish
Transparent Black Forged Wheels
Monoblock · Transparent Black
Matte Black Web-Mesh Forged Wheels
Replica · Matte Black
Wheelforce-Style Gloss Black 10-Spoke Forged Wheels
Monoblock · Gloss Black
Gold 2-Piece 7 Y-Spoke Deep Lip Forged Wheels
2-Piece · Gold
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Brabus Bullit Black Arrow's factory wheel spec reflects a deliberate balance between comfort, steering feel and durability that the engineering team tuned for. Forging lets ANKUSI match that same strength target while trimming rotational mass — the part of a wheel upgrade that actually changes how the car drives, not just how it looks.
The Brabus Bullit Black Arrow runs a 5x112 bolt pattern, 66.6mm center bore, and a F: 19x9.5J wheel from the factory. Our Flush Fitment reference is F 20x10.0J ET30 / R 20x11.0J ET35, which tucks the tire under the fender lip on a stock-height Brabus Bullit Black Arrow. Our Maximum Aggressive reference is F 20x10.5J ET25 / R 20x11.5J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Brabus Bullit Black Arrow OE Wheel Specs
The 2008 Brabus Bullit Black Arrow (Sedan) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are F: 19x9.5J R: 19x10.5J.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Brabus Bullit Black Arrow (2008) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 19x9.5J ET35 → ~6.63″ F backspacing, R 19x10.5J ET35 → ~7.13″ R backspacing
- Flush: F 20x10.0J ET30 → ~6.68″ F backspacing, R 20x11.0J ET35 → ~7.38″ R backspacing
- Max: F 20x10.5J ET25 → ~6.73″ F backspacing, R 20x11.5J ET30 → ~7.43″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Brabus spec, or want a wheel built to a custom offset for your Brabus Bullit Black Arrow? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Brabus Bullit Black Arrow (5x112, 66.6 mm Bore)
In our database, 823 other vehicle entries from 21 makes use exactly the same 5x112 bolt pattern and 66.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 58.6% of those also use a 66.6 mm center bore.
Hub-Centric Rings for a 66.6 mm Center Bore
A wheel with a center bore larger than 66.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 67.1 mm | 67.1 → 66.6 mm |
| 70.1 mm | 70.1 → 66.6 mm |
| 70.5 mm | 70.5 → 66.6 mm |
| 71.6 mm | 71.6 → 66.6 mm |
| 73.1 mm | 73.1 → 66.6 mm |
ANKUSI forged wheels are bored to exactly 66.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Brabus Bullit Black Arrow use?
The 2008 Brabus Bullit Black Arrow uses a 5x112 bolt pattern.
How many lug bolts does the Brabus Bullit Black Arrow use?
The Brabus Bullit Black Arrow uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Brabus Bullit Black Arrow?
The Brabus Bullit Black Arrow's center bore is 66.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Brabus Bullit Black Arrow?
Factory wheels on the Brabus Bullit Black Arrow are F: 19x9.5J R: 19x10.5J.
What is the biggest wheel size I can fit on my Brabus Bullit Black Arrow without rubbing?
The most aggressive fitment we recommend without fender work is F 20x10.5J ET25 / R 20x11.5J ET30. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Brabus Bullit Black Arrow?
For a flush look with minimal to no rubbing, we recommend F 20x10.0J ET30 / R 20x11.0J ET35 as a starting point on a stock or mildly lowered Brabus Bullit Black Arrow.
Do I need wheel spacers for my Brabus Bullit Black Arrow?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Brabus Bullit Black Arrow?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.68" backspacing up front and 7.38" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Brabus Bullit Black Arrow?
Yes — the Brabus Bullit Black Arrow's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x9.5 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.