Holden VY Commodore Bolt Pattern, Center Bore & Wheel Offset (2003)
Holden VY Commodore wheel fitment: 5x120 bolt pattern, 69.6mm center bore. OE wheel sizes and offsets for every VY Commodore variant we cover (4 guides), plus
- 5x120bolt pattern (PCD)
- 69.6 mmcenter bore
- M12x1.5 Nutwheel bolt / nut
- 4 guidesmodel years 2003
Holden VY Commodore wheel specs by year and trim
| Year | Model / trim | Bolt pattern | Center bore | OE wheel |
|---|---|---|---|---|
| 2003 | Holden VY Commodore Acclaim | 5x120 | 69.6 mm | 15x6.5J ET48 |
| 2003 | Holden VY Commodore Executive | 5x120 | 69.6 mm | 15x6.5J ET48 |
| 2003 | Holden VY Commodore S | 5x120 | 69.6 mm | 16x7J ET48 |
| 2003 | Holden VY Commodore SS | 5x120 | 69.6 mm | 18x8J ET48 |
Factory wheel sizes on the Holden VY Commodore
Across the 4 Holden VY Commodore trims with a documented factory wheel, the OE diameter is 15-18 inch, width 6.5-8J and offset ET48. A forged wheel that keeps the 5x120 bolt pattern and the 69.6 mm hub bore and stays inside that offset range bolts on without spacers or hub rings. Going one inch up in diameter with a lower-profile tyre keeps the rolling circumference inside the usual 1.5% tolerance; every extra 0.5J of width moves the outer lip about 6 mm outward at the same offset, and each 5 mm less offset moves the whole wheel 5 mm outward.
Forged wheels for the Holden VY Commodore (5x120)
Shop all Holden VY Commodore forged wheels →
Get a quote for Holden VY Commodore wheels
Vehicles With the Same Hub as the Holden VY Commodore (5x120, 69.6 mm Bore)
In our database, 3 other vehicle entries from 3 makes use exactly the same 5x120 bolt pattern and 69.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x120 is used by 10.3% of the vehicle entries in our database (670 of 6,503); 4.0% of those also use a 69.6 mm center bore.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 15x6.5J | ET48 | 5.64 in (143 mm) | — | — |
| Flush | 17x8J | ET38 | 6.00 in (152 mm) | +9 mm | +29 mm |
| Maximum | 18x8.5J | ET35 | 6.13 in (156 mm) | +12 mm | +38 mm |
Hub-Centric Rings for a 69.6 mm Center Bore
A wheel with a center bore larger than 69.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 70.1 mm | 70.1 → 69.6 mm |
| 70.5 mm | 70.5 → 69.6 mm |
| 71.6 mm | 71.6 → 69.6 mm |
| 72.6 mm | 72.6 → 69.6 mm |
| 73.1 mm | 73.1 → 69.6 mm |
ANKUSI forged wheels are bored to exactly 69.6 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
FAQ
What is the bolt pattern on a Holden VY Commodore?
The Holden VY Commodore uses a 5x120 bolt pattern with a 69.6mm center bore across every VY Commodore variant in our database (4 guides, 2003).
What is the Holden VY Commodore center bore?
The hub-centric center bore is 69.6 mm. Aftermarket wheels should match this bore or use hub-centric rings so the hub, not the bolts, carries the load.
Do all Holden VY Commodore years share the same wheel fitment?
The bolt pattern and center bore are the same across the years we cover, but OE wheel width and offset differ by trim, so check the exact model line before choosing an aftermarket size.
Which forged wheels fit the Holden VY Commodore?
Any wheel drilled 5x120 with a 69.6mm hub bore in the offset range shown on the model guide. ANKUSI forges wheels to order for this exact specification, in 14–24 inch diameters, so no adapters or hub rings are needed.