Dark Gray 10 Y-Spoke Forged Wheels
Monoblock · Dark Gray
2002 Audi RS6 Sedan Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Audi RS6 Sedan wheels? This page gives the 2002 Audi RS6 Sedan bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged Audi RS6 Sedan rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2002 Audi RS6 Sedan uses a 5x112 bolt pattern with a 57.1 mm centre bore and M14x1.5 lug bolts. Factory wheels: 19x9.0J, front and rear. For aftermarket wheels, 20x9.5J ET25 sits flush and 20x10.0J ET20 is the most aggressive fit.
Forged wheels for the 2002 Audi RS6 Sedan — drilled 5x112 with a 57.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Audi RS6 Sedan (2002): 5x112 bolt pattern, 57.1mm center bore. Factory wheels: 19x9.0J F/R. Reference fitment ranges.
Bolt Pattern5x112
Wheel Bolt/NutM14x1.5 Bolt
Center Bore57.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Caliper TypeBrembo 8-piston fixed front caliper (OEM, Audi RS)
Year2002
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x9.0J F/R |
| Flush Fitment | 20x9.5J at ET25 offset |
| Maximum Aggressive | 20x10.0J at ET20 offset |
Forged Wheel Designs for the Audi RS6 Sedan
Every design below is forged to order, so it can be machined to the Audi RS6 Sedan's 5x112 bolt pattern and 57.1 mm center bore, with the width and offset calculated for your setup.
Brushed Side-Milled Silver 10 Y-Spoke Forged Wheels
Monoblock · Brushed Side-milled Silver
Audi OEM-Style Gloss Black Beadlock Forged Wheels
Off-Road Beadlock · Gloss Black
Audi OEM-Style Brushed Silver 5 Y-Spoke Forged Wheels
Monoblock · Brushed Silver
Audi OEM-Style Matte Black 5 Y-Spoke Forged Wheels
Monoblock · Gloss Black
HRE-Style Brushed Champagne Mesh 2-Piece Riveted Deep Lip Forged Wheels
2-Piece · Brushed Champagne / Polished Lip
Rotiform-Style Silver Custom Forged Wheels
Monoblock · Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Audi RS6 Sedan runs a 5x112 bolt pattern, 57.1mm center bore, and a 19x9.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x9.5J ET25, which tucks the tire under the fender lip on a stock-height Audi RS6 Sedan. Our Maximum Aggressive reference is 20x10.0J ET20 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Audi RS6 Sedan OE Wheel Specs
The 2002 Audi RS6 Sedan (Sedan) uses a 5x112 bolt pattern with a 57.1mm center bore. Factory wheels are 19x9.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Audi RS6 Sedan (2002) we drill the 5x112 pattern and cut the centre bore to 57.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x9.0J ET30 → ~6.18″ backspacing
- Flush: 20x9.5J ET25 → ~6.23″ backspacing
- Max: 20x10.0J ET20 → ~6.29″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Audi spec, or want a wheel built to a custom offset for your Audi RS6 Sedan? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Vehicles With the Same Hub as the Audi RS6 Sedan (5x112, 57.1 mm Bore)
In our database, 407 other vehicle entries from 18 makes use exactly the same 5x112 bolt pattern and 57.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 29.0% of those also use a 57.1 mm center bore.
Hub-Centric Rings for a 57.1 mm Center Bore
A wheel with a center bore larger than 57.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 57.1 mm |
| 63.4 mm | 63.4 → 57.1 mm |
| 64.1 mm | 64.1 → 57.1 mm |
| 65.1 mm | 65.1 → 57.1 mm |
| 73.1 mm | 73.1 → 57.1 mm |
ANKUSI forged wheels are bored to exactly 57.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Audi RS6 Sedan use?
The 2002 Audi RS6 Sedan uses a 5x112 bolt pattern.
How many lug bolts does the Audi RS6 Sedan use?
The Audi RS6 Sedan uses a 5-lug bolt pattern (5x112), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Audi RS6 Sedan?
The Audi RS6 Sedan's center bore is 57.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Audi RS6 Sedan?
Factory wheels on the Audi RS6 Sedan are 19x9.0J F/R.
What is the biggest wheel size I can fit on my Audi RS6 Sedan without rubbing?
The most aggressive fitment we recommend without fender work is 20x10.0J at ET20 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Audi RS6 Sedan?
For a flush look with minimal to no rubbing, we recommend 20x9.5J at ET25 offset as a starting point on a stock or mildly lowered Audi RS6 Sedan.
Do I need wheel spacers for my Audi RS6 Sedan?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Audi RS6 Sedan?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.23" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Audi RS6 Sedan?
The Audi RS6 Sedan runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.5, ball-seat lug bolt (13mm radius).
Factory Torque Spec: 120 Nm (89 ft-lb). Shared VW/Audi Group ball-seat bolt spec used across most 5x112 Audi models.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x9 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.