Mercedes-Benz GLK 350 4MATIC (2010) Wheel Fitment
Mercedes-Benz GLK 350 4MATIC (2010): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: 19x7.5J F/R. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 19x7.5J F/R |
| Flush Fitment | 20x8.5J at ET35 offset |
| Maximum Aggressive | 21x9.0J at ET30 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Mercedes-Benz GLK 350 4MATIC's factory suspension tuning already accounts for a specific unsprung mass target. Forged construction lets ANKUSI match the factory strength spec while keeping rotational weight down, which is where the real handling benefit comes from on a taller, heavier SUV platform.
The Mercedes-Benz GLK 350 4MATIC runs a 5x112 bolt pattern, 66.6mm center bore, and a 19x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 20x8.5J ET35, which tucks the tire under the fender lip on a stock-height Mercedes-Benz GLK 350 4MATIC. Our Maximum Aggressive reference is 21x9.0J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Mercedes-Benz GLK 350 4MATIC OE Wheel Specs
The 2010 Mercedes-Benz GLK 350 4MATIC (Crossover) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are 19x7.5J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
Flush Fitment
For a flush look with minimal rubbing, F/R 20x8.5J ET35 is the recommended starting point on a stock or mildly lowered Mercedes-Benz GLK 350 4MATIC.
Maximum Aggressive Fitment
F/R 21x9.0J ET30 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 19x7.5J ET45
Recommended setup: 19x7.5J ET45 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade 20x8.0J ET40
Recommended setup: 20x8.0J ET40 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 20x8.5J ET35
Recommended setup: 20x8.5J ET35 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 21x9.0J ET33
Recommended setup: 21x9.0J ET33 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 21x9.0J ET30
Recommended setup: 21x9.0J ET30 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 19x7.5J ET45 | 20x8.0J ET40 | 20x8.5J ET35 | 21x9.0J ET33 | 21x9.0J ET30 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 19x7.5J ET45
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 20x8.5J ET35
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 21x9.0J ET30
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 19x7.5J ET45 → ~6.02″ backspacing
- Flush: 20x8.5J ET35 → ~6.13″ backspacing
- Max: 21x9.0J ET30 → ~6.18″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Mercedes-Benz spec, or want a wheel built to a custom offset for your Mercedes-Benz GLK 350 4MATIC? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Mercedes-Benz GLK 350 4MATIC use?
How many lug bolts does the Mercedes-Benz GLK 350 4MATIC use?
What is the center bore size on the Mercedes-Benz GLK 350 4MATIC?
What size are the factory (stock) wheels on the Mercedes-Benz GLK 350 4MATIC?
What is the biggest wheel size I can fit on my Mercedes-Benz GLK 350 4MATIC without rubbing?
What does a flush wheel fitment look like on the Mercedes-Benz GLK 350 4MATIC?
Do I need wheel spacers for my Mercedes-Benz GLK 350 4MATIC?
How do I calculate wheel backspacing for my Mercedes-Benz GLK 350 4MATIC?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Mercedes-Benz GLK 350 4MATIC?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.5, ball-seat lug bolt.
Factory Torque Spec: 150 Nm (110 ft-lb). SUV/crossover platforms (GLC/ML/GLE/GL/GLS and similar) generally use the longer 45mm bolt at this spec.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.