Haval OEM-Style Gunmetal 10-Spoke Off-Road Forged Wheels
Off-Road · Gunmetal
2025 Haval H9 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Haval H9 wheels? This page gives the 2025 Haval H9 bolt pattern (6x139.7), centre bore, factory rim size and the offset range for aftermarket and forged Haval H9 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2025 Haval H9 uses a 6x139.7 bolt pattern with a 100.1 mm centre bore. Factory wheels: 18x8J ET36. For aftermarket wheels, 18x9J ET18 sits flush.
Forged wheels for the 2025 Haval H9 — drilled 6x139.7 with a 100.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Haval H9 (2025): 6x139.7 bolt pattern, 100.1mm center bore, OE 18x8J ET36. Forged wheel fitment specs from ANKUSI.
Bolt Pattern6x139.7
Center Bore100.1mm
Year2025
CategorySUV
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x8J ET36 |
| Flush Fitment | 18x9J at ET18 offset |
Forged Wheel Designs for the Haval H9
Every design below is forged to order, so it can be machined to the Haval H9's 6x139.7 bolt pattern and 100.1 mm center bore, with the width and offset calculated for your setup.
Haval OEM-Style Gloss Silver 6-Spoke Off-Road Forged Wheels
Off-Road · Gloss Silver
KMC Gloss Black Exposed Bolt Detail Deep Lip Full-Face Off-Road Forged Wheels
Off-Road · Gloss Black
Matte Black 6-Spoke Deep Lip Forged Wheels
Off-Road · Matte Black
Scorpion Custom Finish 8-Spoke Off-Road Forged Wheels
Off-Road · Custom Finish
Black Bear Matte Black Deep Lip Off-Road Forged Wheels
Off-Road · Matte Black
Polished Square-Mesh Bolted Ring Forged Wheels
Off-Road Beadlock · Polished
Method Race Bright Silver Exposed Bolt Detail Off-Road Forged Wheels
Off-Road · Bright Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Haval H9 ships from the factory on a 6x139.7 bolt pattern with a 100.1mm center bore and a 18x8J ET36 wheel. Our flush reference for the Haval H9 is 18x9J ET18.; our maximum aggressive reference is 20x9J ET12. — beyond that, expect clearance issues against the fender liner without further modification.
Haval H9 OE Wheel Specs
The Haval H9 ships from the factory on 6x139.7 bolt pattern wheels with a 100.1mm center bore. The stock wheel size is 18x8J ET36, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Haval H9 (2025) we drill the 6x139.7 pattern and cut the centre bore to 100.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 18x8J | ET36 | 5.92 in (150 mm) | — | — |
| Flush | 18x9J | ET18 | 5.71 in (145 mm) | −5 mm | +31 mm |
| Maximum | 20x9J | ET12 | 5.47 in (139 mm) | −11 mm | +37 mm |
Vehicles With the Same Hub as the Haval H9 (6x139.7, 100.1 mm Bore)
In our database, 21 other vehicle entries from 8 makes use exactly the same 6x139.7 bolt pattern and 100.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
6x139.7 is used by 4.0% of the vehicle pages in our English fitment guide (258 of 6,503); 8.5% of those also use a 100.1 mm center bore.
Hub-Centric Rings for a 100.1 mm Center Bore
A wheel with a center bore larger than 100.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 106.1 mm | 106.1 → 100.1 mm |
| 108.1 mm | 108.1 → 100.1 mm |
| 110.1 mm | 110.1 → 100.1 mm |
| 130.1 mm | 130.1 → 100.1 mm |
ANKUSI forged wheels are bored to exactly 100.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Haval H9 use?
The 2025 Haval H9 uses a 6x139.7 bolt pattern.
How many lug bolts does the Haval H9 use?
The Haval H9 uses a 6-lug bolt pattern (6x139.7), so you need a 6-lug forged wheel to bolt straight on.
What is the center bore size on the Haval H9?
The Haval H9's center bore is 100.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Haval H9?
Factory wheels on the Haval H9 are 18x8J ET36.
What does a flush wheel fitment look like on the Haval H9?
For a flush look with minimal to no rubbing, we recommend 18x9J at ET18 offset as a starting point on a stock or mildly lowered Haval H9.
Do I need wheel spacers for my Haval H9?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Haval H9?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.71" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Haval H9?
The Haval H9 runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 18x8 wheels · 18 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.