Vossen HF-5-Style Bronze Forged Wheels
Replica · Bronze
2006 Strosek Nissan 350Z Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Strosek Nissan 350Z wheels? This page gives the 2006 Strosek Nissan 350Z bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Strosek Nissan 350Z rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2006 Strosek Nissan 350Z uses a 5x114.3 bolt pattern with a 66.1 mm centre bore and M14x1.5 lug bolts. For aftermarket wheels, 19x9.5J ET20 front / 19x10.5J ET15 rear sits flush.
Forged wheels for the 2006 Strosek Nissan 350Z — drilled 5x114.3 with a 66.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Strosek Nissan 350Z (2006): 5x114.3 bolt pattern, 66.1mm center bore, OE F 19x9J ET30 / R 19x10J ET33. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Wheel Bolt/NutM14x1.5 Bolt
Center Bore66.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2006
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | F 19x9.5J ET20 / R 19x10.5J ET15 |
Forged Wheel Designs for the Strosek Nissan 350Z
Every design below is forged to order, so it can be machined to the Strosek Nissan 350Z's 5x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.
Rays Volk Racing TE37-Style Metallic Gray 6-Spoke Riveted Deep Lip Forged Wheels
Deep Dish · Metallic Gray
BBS RE-V7-Style Gunmetal 7 Y-Spoke Forged Wheels
Replica · Gunmetal
Gloss Black 5-Spoke Machined Face Forged Wheels
Monoblock · Gloss Black
Vossen HF-9-Style Brushed Silver Slotted Dish Forged Wheels
Replica · Brushed Silver
HRE Performance P200-Style Metallic Gray 10 Y-Spoke Parallel Spoke Cut Forged Wheels
Replica · Metallic Gray
Vossen-Style Bright Silver Y-Spoke Mesh Forged Wheels
Monoblock · Bright Silver
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Strosek Nissan 350Z ships from the factory on a 5x114.3 bolt pattern with a 66.1mm center bore and a F 19x9J ET30 / R 19x10J ET33 wheel. Our flush reference for the Strosek Nissan 350Z is F 19x9.5J ET20 / R 19x10.5J ET15.; our maximum aggressive reference is F 20x10J ET15 / R 20x11J ET10. — beyond that, expect clearance issues against the fender liner without further modification.
Strosek Nissan 350Z OE Wheel Specs
The Strosek Nissan 350Z ships from the factory on 5x114.3 bolt pattern wheels with a 66.1mm center bore. The stock wheel size is F 19x9J ET30 / R 19x10J ET33, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Strosek Nissan 350Z (2006) we drill the 5x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 19x9J | ET30 | 6.18 in (157 mm) | — | — |
| Flush | 19x9.5J | ET20 | 6.04 in (153 mm) | −4 mm | +16 mm |
| Maximum | 20x10J | ET15 | 6.09 in (155 mm) | −2 mm | +28 mm |
Vehicles With the Same Hub as the Strosek Nissan 350Z (5x114.3, 66.1 mm Bore)
In our database, 224 other vehicle entries from 8 makes use exactly the same 5x114.3 bolt pattern and 66.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x114.3 is used by 20.0% of the vehicle pages in our English fitment guide (1,300 of 6,503); 17.3% of those also use a 66.1 mm center bore.
Hub-Centric Rings for a 66.1 mm Center Bore
A wheel with a center bore larger than 66.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.6 mm | 66.6 → 66.1 mm |
| 67.1 mm | 67.1 → 66.1 mm |
| 70.1 mm | 70.1 → 66.1 mm |
| 70.5 mm | 70.5 → 66.1 mm |
| 73.1 mm | 73.1 → 66.1 mm |
ANKUSI forged wheels are bored to exactly 66.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Strosek Nissan 350Z use?
The 2006 Strosek Nissan 350Z uses a 5x114.3 bolt pattern.
How many lug bolts does the Strosek Nissan 350Z use?
The Strosek Nissan 350Z uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Strosek Nissan 350Z?
The Strosek Nissan 350Z's center bore is 66.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What does a flush wheel fitment look like on the Strosek Nissan 350Z?
For a flush look with minimal to no rubbing, we recommend F 19x9.5J ET20 / R 19x10.5J ET15 as a starting point on a stock or mildly lowered Strosek Nissan 350Z.
Do I need wheel spacers for my Strosek Nissan 350Z?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Strosek Nissan 350Z?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.04" backspacing up front and 6.34" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Strosek Nissan 350Z?
Yes — the Strosek Nissan 350Z's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Sources and Last Update
Data checked against: avtoreference.com, tirewheelguide.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 19x9 wheels · 19 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.