Cupra Ateca Bolt Pattern, Center Bore & Wheel Offset (2018–2025)
Cupra Ateca wheel fitment: 5x112 bolt pattern, 57.1mm center bore (2018–2025). OE wheel sizes and offsets for every Ateca variant we cover (3 guides), plus fl
- 5x112bolt pattern (PCD)
- 57.1 mmcenter bore
- Boltwheel bolt / nut
- 3 guidesmodel years 2018–2025
Cupra Ateca wheel specs by year and trim
| Year | Model / trim | Bolt pattern | Center bore | OE wheel |
|---|---|---|---|---|
| 2025 | Cupra Ateca | 5x112 | 57.1 mm | 19x8J |
| 2020 | Cupra Ateca | 5x112 | 57.1 mm | 19x8J |
| 2018 | Cupra Ateca | 5x112 | 57.1 mm | 19x8J |
Factory wheel sizes on the Cupra Ateca
Across the 3 Cupra Ateca trims with a documented factory wheel, the OE diameter is 19 inch, width 8J. A forged wheel that keeps the 5x112 bolt pattern and the 57.1 mm hub bore and matches the factory offset listed on the model page bolts on without spacers or hub rings. Going one inch up in diameter with a lower-profile tyre keeps the rolling circumference inside the usual 1.5% tolerance; every extra 0.5J of width moves the outer lip about 6 mm outward at the same offset, and each 5 mm less offset moves the whole wheel 5 mm outward.
Forged wheels for the Cupra Ateca (5x112)
Get a quote for Cupra Ateca wheels
Vehicles With the Same Hub as the Cupra Ateca (5x112, 57.1 mm Bore)
In our database, 395 other vehicle entries from 17 makes use exactly the same 5x112 bolt pattern and 57.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle entries in our database (1,407 of 6,503); 29.0% of those also use a 57.1 mm center bore.
Hub-Centric Rings for a 57.1 mm Center Bore
A wheel with a center bore larger than 57.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 57.1 mm |
| 63.4 mm | 63.4 → 57.1 mm |
| 64.1 mm | 64.1 → 57.1 mm |
| 65.1 mm | 65.1 → 57.1 mm |
| 73.1 mm | 73.1 → 57.1 mm |
ANKUSI forged wheels are bored to exactly 57.1 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
FAQ
What is the bolt pattern on a Cupra Ateca?
The Cupra Ateca uses a 5x112 bolt pattern with a 57.1mm center bore across every Ateca variant in our database (3 guides, 2018–2025).
What is the Cupra Ateca center bore?
The hub-centric center bore is 57.1 mm. Aftermarket wheels should match this bore or use hub-centric rings so the hub, not the bolts, carries the load.
Do all Cupra Ateca years share the same wheel fitment?
The bolt pattern and center bore are the same across the years we cover, but OE wheel width and offset differ by trim, so check the exact model line before choosing an aftermarket size.
Which forged wheels fit the Cupra Ateca?
Any wheel drilled 5x112 with a 57.1mm hub bore in the offset range shown on the model guide. ANKUSI forges wheels to order for this exact specification, in 14–24 inch diameters, so no adapters or hub rings are needed.