1980 Renault Fuego Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Renault Fuego wheels? This page gives the 1980 Renault Fuego bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Renault Fuego rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 1980 Renault Fuego uses a 4x100 bolt pattern with a 60.1 mm centre bore and M12x1.5 lug bolts. Factory wheels: 13x5J ET45. For aftermarket wheels, 14x6J ET40 sits flush.
Forged wheels for the 1980 Renault Fuego — drilled 4x100 with a 60.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Renault Fuego (1980): 4x100 bolt pattern, 60.1mm center bore, OE 13x5J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern4x100
Wheel Bolt/NutM12x1.5 Bolt
Center Bore60.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year1980
CategoryCoupe
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 13x5J ET45 |
| Flush Fitment | 14x6J at ET40 offset |
Forged Wheel Designs for the Renault Fuego
Every design below is forged to order, so it can be machined to the Renault Fuego's 4x100 bolt pattern and 60.1 mm center bore, with the width and offset calculated for your setup.
Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White
BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold
BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold
OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White
Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold
Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Coupes and performance platforms are where rotational mass shows up fastest — in acceleration, in braking, and in how quickly the chassis changes direction. Forging lets us build to the same strength spec as the factory wheel at a meaningfully lower rotational weight, which is where the performance gain actually comes from, not just the visual one.
The Renault Fuego ships from the factory on a 4x100 bolt pattern with a 60.1mm center bore and a 13x5J ET45 wheel. Our flush reference for the Renault Fuego is 14x6J ET40.; our maximum aggressive reference is 15x6.5J ET35. — beyond that, expect clearance issues against the fender liner without further modification.
Renault Fuego OE Wheel Specs
The Renault Fuego ships from the factory on 4x100 bolt pattern wheels with a 60.1mm center bore. The stock wheel size is 13x5J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Renault Fuego (1980) we drill the 4x100 pattern and cut the centre bore to 60.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 13x5J | ET45 | 4.77 in (121 mm) | — | — |
| Flush | 14x6J | ET40 | 5.07 in (129 mm) | +8 mm | +18 mm |
| Maximum | 15x6.5J | ET35 | 5.13 in (130 mm) | +9 mm | +29 mm |
Vehicles With the Same Hub as the Renault Fuego (4x100, 60.1 mm Bore)
In our database, 149 other vehicle entries from 10 makes use exactly the same 4x100 bolt pattern and 60.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
4x100 is used by 6.9% of the vehicle pages in our English fitment guide (451 of 6,503); 33.3% of those also use a 60.1 mm center bore.
Hub-Centric Rings for a 60.1 mm Center Bore
A wheel with a center bore larger than 60.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 63.4 mm | 63.4 → 60.1 mm |
| 64.1 mm | 64.1 → 60.1 mm |
| 65.1 mm | 65.1 → 60.1 mm |
| 66.1 mm | 66.1 → 60.1 mm |
| 73.1 mm | 73.1 → 60.1 mm |
ANKUSI forged wheels are bored to exactly 60.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Renault Fuego use?
The 1980 Renault Fuego uses a 4x100 bolt pattern.
How many lug bolts does the Renault Fuego use?
The Renault Fuego uses a 4-lug bolt pattern (4x100), so you need a 4-lug forged wheel to bolt straight on.
What is the center bore size on the Renault Fuego?
The Renault Fuego's center bore is 60.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Renault Fuego?
Factory wheels on the Renault Fuego are 13x5J ET45.
What does a flush wheel fitment look like on the Renault Fuego?
For a flush look with minimal to no rubbing, we recommend 14x6J at ET40 offset as a starting point on a stock or mildly lowered Renault Fuego.
Do I need wheel spacers for my Renault Fuego?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Renault Fuego?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.07" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Renault Fuego?
The Renault Fuego runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 13x5 wheels · 13 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.