Porsche OEM-Style Gloss Black 10 Y-Spoke Forged Wheels
Monoblock · Gloss Black
2026 Porsche 911 Carrera T Club Coupe Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche 911 Carrera T Club Coupe wheels? This page gives the 2026 Porsche 911 Carrera T Club Coupe bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche 911 Carrera T Club Coupe rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche 911 Carrera T Club Coupe (2026): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 20x8.5J R: 21x11.5J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Caliper TypeFixed 4-piston caliper, all four corners (OEM, Porsche)
Year2026
CategorySports Coupe
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x8.5J R: 21x11.5J |
| Flush Fitment | F 20x8.5J ET50 / R 21x11.5J ET66 |
| Maximum Aggressive | F 20x9J ET41 / R 21x11.5J ET58 |
Forged Wheel Designs for the Porsche 911 Carrera T Club Coupe
Every design below is forged to order, so it can be machined to the Porsche 911 Carrera T Club Coupe's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Work-Style Chrome 2-Piece Deep Lip Forged Wheels
2-Piece · Chrome
FACE Gunmetal 5 Y-Spoke Forged Wheels
Replica · Gunmetal
Black / Machined Petal Machined Face Forged Wheels
Monoblock · Black Machined
HRE-Style Hyper Silver 5-Spoke Rotor Forged Wheels
Monoblock · Hyper Silver
Rays-Style Bronze 5 Y-Spoke Forged Wheels
Monoblock · Bronze
Gloss Black Rotary 5-Spoke Forged Wheels
Monoblock · Gloss Black
BBS-Style Brushed Silver Mesh Forged Wheels
Deep Dish · Matte Silver
See all Porsche 911 wheel designs Porsche OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a performance-oriented coupe, the wheel is one of the few components where shaving weight has a compounding effect - less rotational mass means less work for the brakes, the drivetrain, and the chassis on every input. A forged wheel gets there without compromising the strength margin the factory engineered in.
The Porsche 911 Carrera T Club Coupe runs a 5x130 fitment, 71.6mm center bore, and a F: 20x8.5J wheel from the factory. Our Flush Fitment reference is F 20x8.5J ET50 / R 21x11.5J ET66 - on this car the published aftermarket guidance is that the factory footprint already sits flush. Our Maximum Aggressive reference is F 20x9J ET41 / R 21x11.5J ET58 - beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche 911 Carrera T Club Coupe OE Wheel Specs
The 2026 Porsche 911 Carrera T Club Coupe (Sports Coupe) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 20x8.5J R: 21x11.5J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche 911 Carrera T Club Coupe (2026) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
APEX VS-5RS forged offered 19/20 and 20/21 across the 992 Carrera/Targa family 5-lug 5x130 CB71.6 hubcentric. Verified on 992 Carrera/Targa platform (APEX 992 Carrera/Targa guide)
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 20x8.5J ET50 → ~6.72″ F backspacing, R 21x11.5J ET66 → ~8.85″ R backspacing
- Flush: F 20x8.5J ET50 → ~6.72″ F backspacing, R 21x11.5J ET66 → ~8.85″ R backspacing
- Max: F 20x9J ET41 → ~6.61″ F backspacing, R 21x11.5J ET58 → ~8.53″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche 911 Carrera T Club Coupe? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche 911 Carrera T Club Coupe use?
The 2026 Porsche 911 Carrera T Club Coupe uses a 5x130 bolt pattern.
How many lug bolts does the Porsche 911 Carrera T Club Coupe use?
The Porsche 911 Carrera T Club Coupe uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche 911 Carrera T Club Coupe?
The Porsche 911 Carrera T Club Coupe's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche 911 Carrera T Club Coupe?
Factory wheels on the Porsche 911 Carrera T Club Coupe are F: 20x8.5J R: 21x11.5J.
What is the biggest wheel size I can fit on my Porsche 911 Carrera T Club Coupe without rubbing?
The most aggressive fitment we recommend without fender work is F 20x9J ET41 / R 21x11.5J ET58. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche 911 Carrera T Club Coupe?
For a flush look with minimal to no rubbing, we recommend F 20x8.5J ET50 / R 21x11.5J ET66 as a starting point on a stock or mildly lowered Porsche 911 Carrera T Club Coupe.
Do I need wheel spacers for my Porsche 911 Carrera T Club Coupe?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche 911 Carrera T Club Coupe?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.72" backspacing up front and 8.85" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche 911 Carrera T Club Coupe?
Yes — the Porsche 911 Carrera T Club Coupe's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.