Brushed Silver 20 Directional-Spoke Forged Wheels
Monoblock · Matte Silver
1993 Porsche 911 Carrera 4 30 Years Edition Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Porsche 911 Carrera 4 30 Years Edition wheels? This page gives the 1993 Porsche 911 Carrera 4 30 Years Edition bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Porsche 911 Carrera 4 30 Years Edition rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Porsche 911 Carrera 4 30 Years Edition (1993): 5x130 bolt pattern, 71.6mm center bore. Factory wheels: F: 17x7J R: 17x9J. Reference fitment ranges.
Bolt Pattern5x130
Wheel Bolt/NutM14x1.5 Bolt
Center Bore71.6mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Caliper TypeFixed 4-piston caliper, all four corners (OEM, Porsche)
Year1993
CategorySports Coupe
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 17x7J R: 17x9J |
| Flush Fitment | F 17x8J ET47 / R 17x9J ET47 |
| Maximum Aggressive | F 18x8.5J ET52 / R 18x10J ET30 |
Forged Wheel Designs for the Porsche 911 Carrera 4 30 Years Edition
Every design below is forged to order, so it can be machined to the Porsche 911 Carrera 4 30 Years Edition's 5x130 bolt pattern and 71.6 mm center bore, with the width and offset calculated for your setup.
Gold Cross-Spoke Mesh 2-Piece Polished Lip Forged Wheels
2-Piece · Gold / Polished Lip
Brushed Silver Mesh Deep-Lip Forged Wheels
2-Piece · Custom Finish
BBS LM-Style Silver 5 Y-Spoke Mirror Polished Forged Wheels
Replica · Silver
Gloss Black / Gunmetal / Gray Petal Forged Wheels
Monoblock · Gloss Black / Gunmetal / Gray
Polished Turbine Forged Wheels
Monoblock · Polished
HRE-Style 2-Piece Satin Black 5-Spoke Riveted Lip Forged Wheels
2-Piece · Satin Black
See all Porsche 911 wheel designs Porsche OEM-Style Forged Wheels
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a performance-oriented coupe, the wheel is one of the few components where shaving weight has a compounding effect - less rotational mass means less work for the brakes, the drivetrain, and the chassis on every input. A forged wheel gets there without compromising the strength margin the factory engineered in.
The Porsche 911 Carrera 4 30 Years Edition runs a 5x130 fitment, 71.6mm center bore, and a F: 17x7J wheel from the factory. Our Flush Fitment reference is F 17x8J ET47 / R 17x9J ET47, which tucks the tire under the fender lip on a stock-height Porsche 911 Carrera 4 30 Years Edition. Our Maximum Aggressive reference is F 18x8.5J ET52 / R 18x10J ET30 - beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Porsche 911 Carrera 4 30 Years Edition OE Wheel Specs
The 1993 Porsche 911 Carrera 4 30 Years Edition (Sports Coupe) uses a 5x130 bolt pattern with a 71.6mm center bore. Factory wheels are F: 17x7J R: 17x9J.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Porsche 911 Carrera 4 30 Years Edition (1993) we drill the 5x130 pattern and cut the centre bore to 71.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Real-World Fitment Notes
964 Carrera 4 runs Cup 17s, Design 90, or APEX ARC-8; Turbo-look flared 30-Jahre cars take wider rears 5x130 / 71.6 CB; 964 platform data (Wheel-Size/APEX)
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 17x7J ET55 → ~6.17″ F backspacing, R 17x9J ET55 → ~7.17″ R backspacing
- Flush: F 17x8J ET47 → ~6.35″ F backspacing, R 17x9J ET47 → ~6.85″ R backspacing
- Max: F 18x8.5J ET52 → ~6.8″ F backspacing, R 18x10J ET30 → ~6.68″ R backspacing
A Note on Clearance
Final clearance depends on the exact tire model, suspension height, brake package, alignment and vehicle tolerances. A physical test fit is recommended before production.
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Porsche spec, or want a wheel built to a custom offset for your Porsche 911 Carrera 4 30 Years Edition? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Porsche 911 Carrera 4 30 Years Edition use?
The 1993 Porsche 911 Carrera 4 30 Years Edition uses a 5x130 bolt pattern.
How many lug bolts does the Porsche 911 Carrera 4 30 Years Edition use?
The Porsche 911 Carrera 4 30 Years Edition uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Porsche 911 Carrera 4 30 Years Edition?
The Porsche 911 Carrera 4 30 Years Edition's center bore is 71.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Porsche 911 Carrera 4 30 Years Edition?
Factory wheels on the Porsche 911 Carrera 4 30 Years Edition are F: 17x7J R: 17x9J.
What is the biggest wheel size I can fit on my Porsche 911 Carrera 4 30 Years Edition without rubbing?
The most aggressive fitment we recommend without fender work is F 18x8.5J ET52 / R 18x10J ET30. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Porsche 911 Carrera 4 30 Years Edition?
For a flush look with minimal to no rubbing, we recommend F 17x8J ET47 / R 17x9J ET47 as a starting point on a stock or mildly lowered Porsche 911 Carrera 4 30 Years Edition.
Do I need wheel spacers for my Porsche 911 Carrera 4 30 Years Edition?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Porsche 911 Carrera 4 30 Years Edition?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.35" backspacing up front and 6.85" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Porsche 911 Carrera 4 30 Years Edition?
Yes — the Porsche 911 Carrera 4 30 Years Edition's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.