Gloss Black Machined 5-Star Split-Spoke Forged Wheels
Monoblock · Gloss Black
2007 Nissan Altima Hybrid Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Nissan Altima Hybrid wheels? This page gives the 2007 Nissan Altima Hybrid bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Nissan Altima Hybrid rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Nissan Altima Hybrid (2007): 5x114.3 bolt pattern, 66.1mm center bore, OE 16x7J ET45. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.25 Nut
Center Bore66.1mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2007
Category5-Lug Performance / Tuner
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x7J ET45 |
| Flush Fitment | 18x8J at ET35 offset |
Forged Wheel Designs for the Nissan Altima Hybrid
Every design below is forged to order, so it can be machined to the Nissan Altima Hybrid's 5x114.3 bolt pattern and 66.1 mm center bore, with the width and offset calculated for your setup.
Brushed Silver Turbine Disc Forged Wheels
Monoblock · Brushed Silver
Vossen Gloss Black Double-Ring Forged Wheels
Replica · Gloss Black
Rays Volk Racing CE28N-Style Gloss White 10-Spoke Forged Wheels
Replica · Gloss White
Wheelforce-Style Transparent Gray Brushed 10-Spoke Star Forged Wheels
Monoblock · Transparent Gray
Hyper Silver 6-Spoke Forged Wheels
Monoblock · Hyper Silver
Rays-Style Gloss Black 5-Spoke Forged Wheels
Replica · Gloss Black
Metallic Gray 5 Y-Spoke Concave Forged Wheels
Concave · Metallic Gray
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The Nissan Altima Hybrid ships from the factory on a 5x114.3 bolt pattern with a 66.1mm center bore and a 16x7J ET45 wheel. Our flush reference for the Nissan Altima Hybrid is 18x8J ET35.; our maximum aggressive reference is 19x8.5J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Nissan Altima Hybrid OE Wheel Specs
The Nissan Altima Hybrid ships from the factory on 5x114.3 bolt pattern wheels with a 66.1mm center bore. The stock wheel size is 16x7J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Nissan Altima Hybrid (2007) we drill the 5x114.3 pattern and cut the centre bore to 66.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 16x7J ET45: backspacing ≈ 5.77"
- Flush 18x8J ET35: backspacing ≈ 5.88"
- Max 19x8.5J ET30: backspacing ≈ 5.93"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Nissan Altima Hybrid.
Frequently Asked Questions
What bolt pattern (PCD) does the Nissan Altima Hybrid use?
The 2007 Nissan Altima Hybrid uses a 5x114.3 bolt pattern.
How many lug bolts does the Nissan Altima Hybrid use?
The Nissan Altima Hybrid uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Nissan Altima Hybrid?
The Nissan Altima Hybrid's center bore is 66.1mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Nissan Altima Hybrid?
Factory wheels on the Nissan Altima Hybrid are 16x7J ET45.
What does a flush wheel fitment look like on the Nissan Altima Hybrid?
For a flush look with minimal to no rubbing, we recommend 18x8J at ET35 offset as a starting point on a stock or mildly lowered Nissan Altima Hybrid.
Do I need wheel spacers for my Nissan Altima Hybrid?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Nissan Altima Hybrid?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.88" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Nissan Altima Hybrid?
The Nissan Altima Hybrid runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.25, conical-seat lug nut.
Factory Torque Spec: 103-122 Nm (76-90 ft-lb). Range covers most Nissan passenger cars and crossovers on M12x1.25 studs.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.