2005 Holden Tigra Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Holden Tigra wheels? This page gives the 2005 Holden Tigra bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Holden Tigra rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2005 Holden Tigra uses a 4x100 bolt pattern with a 56.6 mm centre bore and M12x1.5 lug nuts. Factory wheels: 16x6.5J ET40. For aftermarket wheels, 17x7J ET35 sits flush.
Forged wheels for the 2005 Holden Tigra — drilled 4x100 with a 56.6 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Holden Tigra (2005): 4x100 bolt pattern, 56.6mm center bore, OE 16x6.5J ET40. Forged wheel fitment specs from ANKUSI.
Bolt Pattern4x100
Wheel Bolt/NutM12x1.5 Nut
Center Bore56.6mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2005
CategoryConvertible
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x6.5J ET40 |
| Flush Fitment | 17x7J at ET35 offset |
Forged Wheel Designs for the Holden Tigra
Every design below is forged to order, so it can be machined to the Holden Tigra's 4x100 bolt pattern and 56.6 mm center bore, with the width and offset calculated for your setup.
BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White
BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold
BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold
Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold
OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White
Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Convertibles lose some of the structural rigidity a fixed roof provides, which means the suspension and wheels end up doing more of the work to keep the chassis composed. A forged wheel keeps unsprung mass down without sacrificing the strength margin the factory built in — useful on a platform that's already managing extra flex.
The Holden Tigra ships from the factory on a 4x100 bolt pattern with a 56.6mm center bore and a 16x6.5J ET40 wheel. Our flush reference for the Holden Tigra is 17x7J ET35.; our maximum aggressive reference is 17x7.5J ET32. — beyond that, expect clearance issues against the fender liner without further modification.
Holden Tigra OE Wheel Specs
The Holden Tigra ships from the factory on 4x100 bolt pattern wheels with a 56.6mm center bore. The stock wheel size is 16x6.5J ET40, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Holden Tigra (2005) we drill the 4x100 pattern and cut the centre bore to 56.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 16x6.5J | ET40 | 5.32 in (135 mm) | — | — |
| Flush | 17x7J | ET35 | 5.38 in (137 mm) | +1 mm | +11 mm |
| Maximum | 17x7.5J | ET32 | 5.51 in (140 mm) | +5 mm | +21 mm |
Vehicles With the Same Hub as the Holden Tigra (4x100, 56.6 mm Bore)
In our database, 58 other vehicle entries from 7 makes use exactly the same 4x100 bolt pattern and 56.6 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
4x100 is used by 6.9% of the vehicle pages in our English fitment guide (451 of 6,503); 13.1% of those also use a 56.6 mm center bore.
Hub-Centric Rings for a 56.6 mm Center Bore
A wheel with a center bore larger than 56.6 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 57.1 mm | 57.1 → 56.6 mm |
| 60.1 mm | 60.1 → 56.6 mm |
| 63.4 mm | 63.4 → 56.6 mm |
| 64.1 mm | 64.1 → 56.6 mm |
| 73.1 mm | 73.1 → 56.6 mm |
ANKUSI forged wheels are bored to exactly 56.6 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
What bolt pattern (PCD) does the Holden Tigra use?
The 2005 Holden Tigra uses a 4x100 bolt pattern.
How many lug bolts does the Holden Tigra use?
The Holden Tigra uses a 4-lug bolt pattern (4x100), so you need a 4-lug forged wheel to bolt straight on.
What is the center bore size on the Holden Tigra?
The Holden Tigra's center bore is 56.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Holden Tigra?
Factory wheels on the Holden Tigra are 16x6.5J ET40.
What does a flush wheel fitment look like on the Holden Tigra?
For a flush look with minimal to no rubbing, we recommend 17x7J at ET35 offset as a starting point on a stock or mildly lowered Holden Tigra.
Do I need wheel spacers for my Holden Tigra?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Holden Tigra?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.38" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Holden Tigra?
The Holden Tigra runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Other cars on the same factory size: 16x6.5 wheels · 16 inch wheels.
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.