
2014 Geely SC3 Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Geely SC3 wheels? This page gives the 2014 Geely SC3 bolt pattern (4x100), centre bore, factory rim size and the offset range for aftermarket and forged Geely SC3 rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Geely SC3 (2014): 4x100 bolt pattern, 57.1mm center bore. Factory wheels: 14x5J F/R. Flush and max fitment confirmed on request.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 19, 2026. How we verify
Forged Wheel Designs for the Geely SC3
Every design below is forged to order, so it can be machined to the Geely SC3's 4x100 bolt pattern and 57.1 mm center bore, with the width and offset calculated for your setup.


Rotiform-Style Gloss White 6-Spoke Forged Wheels
Monoblock · Gloss White

BBS LM-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal

BBS-Style Gold Mesh Polished Lip 2-Piece Forged Wheels
2-Piece · Gold

BBS-Style Gold Mesh Polished Lip Forged Wheels
Monoblock · Gold

OZ Racing-Style Gloss White 15-Spoke Forged Wheels
Monoblock · Gloss White

Bronze Gold Cross-Spoke Forged Wheels
Monoblock · Bronze Gold

Rays-Style Gunmetal Mesh Polished Deep Lip Forged Wheels
Deep Dish · Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


ANKUSI Engineering Expert Advice
A big saloon lives or dies on ride quality, and the wheel is the first thing that ruins it. Going wider and lower without watching load rating and offset trades away exactly the composure you paid for. Forging lets you add diameter and width while keeping rotating mass close to the factory figure.
We publish the factory specification for the Geely SC3 below. We have not yet been able to verify aftermarket flush or maximum-aggressive offsets for this exact variant against a source we trust, so we are not listing any - an invented offset is worse than no offset when a wheel has to clear a caliper.
Geely SC3 OE Wheel Specs
The 2014 Geely SC3 (Performance Sedan) uses a 4x100 bolt pattern with a 57.1mm center bore. Factory wheels are 14x5J F/R.
Why the factory spec works for most owners:
- Keeps unsprung weight low to preserve the factory handling balance
- Matches the wider, performance-oriented tire sizing typical of this platform
- Maintains clearance for the factory brake package and suspension geometry
- Balances grip with ride comfort for daily and spirited driving
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Geely SC3 (2014) we drill the 4x100 pattern and cut the centre bore to 57.1mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Aftermarket Fitment: Confirmed on Request
Published aftermarket fitment for this exact variant is still thin, so we have not committed to a flush or maximum-aggressive figure. Our engineering team is still collecting verified data for this variant. In the meantime the factory specification above is accurate and is the safe reference point for ordering.
Need a wheel for this car now? Contact ANKUSI with your target diameter, width and offset and our engineers will confirm the correct forged spec against your brake package before anything is cut. You can also use our Offset & Backspacing Calculator to work through the numbers yourself.