Belak-Style 2-Piece 5-Spoke Beadlock Mirror Milled Forged Drag Racing Wheels
Drag Racing · Custom Finish
2022 Ford Ford GT Alan Mann Heritage Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Ford Ford GT Alan Mann Heritage wheels? This page gives the 2022 Ford Ford GT Alan Mann Heritage bolt pattern (5x114.3), centre bore, factory rim size and the offset range for aftermarket and forged Ford Ford GT Alan Mann Heritage rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Ford Ford GT Alan Mann Heritage (2022): 5x114.3 bolt pattern, 70.5mm center bore. Factory wheels: F: 20x8.5J R: 20x11.5J. Reference fitment ranges.
Bolt Pattern5x114.3
Wheel Bolt/NutM12x1.5 Nut
Center Bore70.5mm
Wheel Load Rating700–850 kg/wheel (Performance / Sports Car segment reference)
Year2022
CategorySupercar
Data check: the bolt pattern and center bore on this page have not yet been confirmed by a second independent source. Measure your hub or ask us before ordering. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 20x8.5J R: 20x11.5J |
| Flush Fitment | F 20x9.0J ET35 / R 20x12.0J ET42 |
| Maximum Aggressive | F 20x9.5J ET30 / R 20x12.5J ET38 |
Forged Wheel Designs for the Ford Ford GT Alan Mann Heritage
Every design below is forged to order, so it can be machined to the Ford Ford GT Alan Mann Heritage's 5x114.3 bolt pattern and 70.5 mm center bore, with the width and offset calculated for your setup.
Forgiato-Style Satin Black Swirl Multi-Spoke Floating Cap Forged Wheels
Monoblock · Satin Black
Ford Mustang OEM-Style Gloss Black Mesh 2-Piece Deep Lip Forged Wheels
2-Piece · Custom Finish
Vossen Bright Silver 5 Y-Spoke Brushed Double-Ring Forged Wheels
Replica · Bright Silver
Ford Mustang OEM-Style Gunmetal Mesh Forged Wheels
Monoblock · Gunmetal
Gloss Black 10 Y-Spoke Forged Wheels
Monoblock · Gloss Black
Vossen-Style Gloss Black Windowed Dish Forged Wheels
Replica · Gloss Black
Vossen Gloss Black Double-Ring Forged Wheels
Replica · Gloss Black
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
On a supercar, wheel weight is one of the few remaining places to cut rotational mass without touching the powertrain or chassis the factory already optimized. Forging gets there at the same structural margin as the OE wheel, which is exactly the trade a car built around outright performance rewards.
The Ford Ford GT Alan Mann Heritage runs a 5x114.3 bolt pattern, 70.5mm center bore, and a F: 20x8.5J wheel from the factory. Our Flush Fitment reference is F 20x9.0J ET35 / R 20x12.0J ET42, which tucks the tire under the fender lip on a stock-height Ford Ford GT Alan Mann Heritage. Our Maximum Aggressive reference is F 20x9.5J ET30 / R 20x12.5J ET38 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Ford GT Alan Mann Heritage OE Wheel Specs
The 2022 Ford Ford GT Alan Mann Heritage (Supercar) uses a 5x114.3 bolt pattern with a 70.5mm center bore. Factory wheels are F: 20x8.5J R: 20x11.5J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday drivability
- A commonly used size for this vehicle class, supporting parts and tire availability
- Maintains clearance for the factory suspension and brake components
- Provides stable, predictable handling across normal driving conditions
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Ford Ford GT Alan Mann Heritage (2022) we drill the 5x114.3 pattern and cut the centre bore to 70.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 20x8.5J ET42 → ~6.4″ F backspacing, R 20x11.5J ET50 → ~8.22″ R backspacing
- Flush: F 20x9.0J ET35 → ~6.38″ F backspacing, R 20x12.0J ET42 → ~8.15″ R backspacing
- Max: F 20x9.5J ET30 → ~6.43″ F backspacing, R 20x12.5J ET38 → ~8.25″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Ford GT Alan Mann Heritage? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Ford GT Alan Mann Heritage use?
The 2022 Ford Ford GT Alan Mann Heritage uses a 5x114.3 bolt pattern.
How many lug bolts does the Ford Ford GT Alan Mann Heritage use?
The Ford Ford GT Alan Mann Heritage uses a 5-lug bolt pattern (5x114.3), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the Ford Ford GT Alan Mann Heritage?
The Ford Ford GT Alan Mann Heritage's center bore is 70.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the Ford Ford GT Alan Mann Heritage?
Factory wheels on the Ford Ford GT Alan Mann Heritage are F: 20x8.5J R: 20x11.5J.
What is the biggest wheel size I can fit on my Ford Ford GT Alan Mann Heritage without rubbing?
The most aggressive fitment we recommend without fender work is F 20x9.5J ET30 / R 20x12.5J ET38. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the Ford Ford GT Alan Mann Heritage?
For a flush look with minimal to no rubbing, we recommend F 20x9.0J ET35 / R 20x12.0J ET42 as a starting point on a stock or mildly lowered Ford Ford GT Alan Mann Heritage.
Do I need wheel spacers for my Ford Ford GT Alan Mann Heritage?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Ford Ford GT Alan Mann Heritage?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.38" backspacing up front and 8.15" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Ford Ford GT Alan Mann Heritage?
Yes — the Ford Ford GT Alan Mann Heritage's factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.