
WF Metallic Gray 10-Spoke Forged Wheels
Replica · Metallic Gray
Fitting BMW iX1 U11 (UK) wheels? This page gives the 2023 BMW iX1 U11 (UK) bolt pattern (5x112), centre bore, factory rim size and the offset range for aftermarket and forged BMW iX1 U11 (UK) rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
BMW iX1 U11 (UK) (2023): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: 18x7.5J F/R. Reference fitment ranges.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 18x7.5J F/R |
| Flush Fitment | 19x8.5J at ET35 offset |
| Maximum Aggressive | 20x9.0J at ET30 offset |
Every design below is forged to order, so it can be machined to the BMW iX1 U11 (UK)'s 5x112 bolt pattern and 66.6 mm center bore, with the width and offset calculated for your setup.

Replica · Metallic Gray

Replica · Satin Light Gold

Replica · Gloss Black / Gunmetal


Monoblock · Gloss Black

2-Piece · Matte Silver

Monoblock · Polished

Monoblock · Mirror Polished
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.


Because an SUV's center of gravity is already higher than a sedan's, anything added at the corners — including wheel weight — has an outsized effect on handling balance. A forged wheel lets us hit the visual stance owners want without adding the rotational mass a cast wheel of the same strength would carry.
The BMW iX1 U11 (UK) runs a 5x112 bolt pattern, 66.6mm center bore, and a 18x7.5J, front and rear, wheel from the factory. Our Flush Fitment reference is 19x8.5J ET35, which tucks the tire under the fender lip on a stock-height BMW iX1 U11 (UK). Our Maximum Aggressive reference is 20x9.0J ET30 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
The 2023 BMW iX1 U11 (UK) (Crossover) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are 18x7.5J F/R.
Why the factory spec works for most owners:
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the BMW iX1 U11 (UK) (2023) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact BMW spec, or want a wheel built to a custom offset for your BMW iX1 U11 (UK)? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Thread & Fastener: M14x1.25, 60-degree conical-seat lug bolt.
Factory Torque Spec: 140 Nm (103 ft-lb). Consistent across modern BMW passenger and X-series models using factory conical-seat bolts.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.