BMW iX I20 (2022) Bolt Pattern & Wheel Fitment
BMW iX I20 (2022): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: 21x9.0J F/R. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 21x9.0J F/R |
| Flush Fitment | 22x10.0J at ET28 offset |
| Maximum Aggressive | 23x10.5J at ET25 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The BMW iX I20 runs a 5x112 bolt pattern, 66.6mm center bore, and a 21x9.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 22x10.0J ET28, which tucks the tire under the fender lip on a stock-height BMW iX I20. Our Maximum Aggressive reference is 23x10.5J ET25 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
BMW iX OE Wheel Specs
The 2022 BMW iX I20 (EV SUV) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are 21x9.0J F/R.
Why the factory spec works for most owners:
- Supports the vehicle's curb weight and load capacity
- Preserves ground clearance for everyday and light off-road use
- Balances ride comfort with cargo and passenger stability
- Maintains clearance for the factory suspension travel and brake package
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the BMW iX I20 (2022) we drill the 5x112 pattern and cut the centre bore to 66.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look with minimal rubbing, F/R 22x10.0J ET28 is the recommended starting point on a stock or mildly lowered BMW iX I20.
Maximum Aggressive Fitment
F/R 23x10.5J ET25 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 21x9.0J ET35
Recommended setup: 21x9.0J ET35 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade 22x9.5J ET32
Recommended setup: 22x9.5J ET32 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 22x10.0J ET28
Recommended setup: 22x10.0J ET28 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 23x10.5J ET27
Recommended setup: 23x10.5J ET27 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 23x10.5J ET25
Recommended setup: 23x10.5J ET25 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 21x9.0J ET35 | 22x9.5J ET32 | 22x10.0J ET28 | 23x10.5J ET27 | 23x10.5J ET25 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 21x9.0J ET35
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 22x10.0J ET28
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 23x10.5J ET25
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 21x9.0J ET35 → ~6.38″ backspacing
- Flush: 22x10.0J ET28 → ~6.6″ backspacing
- Max: 23x10.5J ET25 → ~6.73″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact BMW spec, or want a wheel built to a custom offset for your BMW iX I20? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Custom Forged Wheels for the BMW iX I20 (2022)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x112 pattern and the 66.6mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most BMW orders on this platform land somewhere between the 22x10.0J ET28 flush setup and the 23x10.5J ET25 aggressive setup referenced above.
Designs we already tool for the 5x112 pattern — each one is re-cut to your sizes and offsets:
Matte Silver Forged Wheels – Porsche 911 / BMW M3 Fitment (5-Lug)
Rays Volk Racing TE37 Bronze 6-Spoke Deep Lip Forged Wheels – Porsche 911 / BMW M3 Fitment (5-Lug)
APEX VS-5RS Bright Silver 5 Y-Spoke Forged Wheels – Porsche 911 / BMW M3 Fitment (5-Lug)
Transparent Green Forged Wheels – Porsche 911 / BMW M3 Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the BMW iX I20 use?
How many lug bolts does the BMW iX I20 use?
What is the center bore size on the BMW iX I20?
What size are the factory (stock) wheels on the BMW iX I20?
What is the biggest wheel size I can fit on my BMW iX I20 without rubbing?
What does a flush wheel fitment look like on the BMW iX I20?
Do I need wheel spacers for my BMW iX I20?
How do I calculate wheel backspacing for my BMW iX I20?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my BMW iX I20?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.25, 60-degree conical-seat lug bolt.
Factory Torque Spec: 140 Nm (103 ft-lb). Consistent across modern BMW passenger and X-series models using factory conical-seat bolts.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.