Metallic Gray Split Directional Milled Forged Wheels
Monoblock · Metallic Gray
2009 BMW 7-Series F01 (UK) Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting BMW 7-Series F01 (UK) wheels? This page gives the 2009 BMW 7-Series F01 (UK) bolt pattern (5x120), centre bore, factory rim size and the offset range for aftermarket and forged BMW 7-Series F01 (UK) rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
BMW 7-Series F01 (UK) (2009): 5x120 bolt pattern, 72.6mm center bore. Factory wheels: F: 18x8.0J R: 18x8.0J. Reference fitment ranges.
Bolt Pattern5x120
Wheel Bolt/NutM12x1.5 Bolt
Center Bore72.6mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2009
CategorySedan
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 18x8.0J R: 18x8.0J |
| Flush Fitment | F 19x8.5J ET20 / R 19x9.5J ET25 |
| Maximum Aggressive | F 20x9.0J ET18 / R 20x10.0J ET22 |
Forged Wheel Designs for the BMW 7-Series F01 (UK)
Every design below is forged to order, so it can be machined to the BMW 7-Series F01 (UK)'s 5x120 bolt pattern and 72.6 mm center bore, with the width and offset calculated for your setup.
Brushed Silver 10 Y-Mesh Forged Wheels
Monoblock · Matte Silver
Gold 3-Spoke Polished Lip Forged Wheels
Monoblock · Gold
MD Off Road Gloss Black Deep Lip Exposed Bolt Detail Double Ring Lip Forged Wheels
Deep Dish · Gloss Black
BMW Style 763M Matte Black 5 Y-Spoke Forged Wheels
Replica · Matte Black
Black / Machined Directional Milled Machined Face Forged Wheels
Monoblock · Black Machined
Matte Navy Blue 6-Spoke Forged Wheels
Monoblock · Matte Navy Blue
Silver / Gunmetal 5-Spoke Forged Wheels
Monoblock · Silver / Gunmetal
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Most of the engineering value in a forged wheel over a cast one shows up in rotational mass, not outright strength — both can meet the same load rating, but the forged piece gets there lighter. On a sedan platform tuned for everyday balance, that weight saving is felt directly in steering response and ride quality.
The BMW 7-Series F01 (UK) runs a 5x120 bolt pattern, 72.6mm center bore, and a F: 18x8.0J wheel from the factory. Our Flush Fitment reference is F 19x8.5J ET20 / R 19x9.5J ET25, which tucks the tire under the fender lip on a stock-height BMW 7-Series F01 (UK). Our Maximum Aggressive reference is F 20x9.0J ET18 / R 20x10.0J ET22 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
BMW 7-Series (UK) OE Wheel Specs
The 2009 BMW 7-Series F01 (UK) (Sedan) uses a 5x120 bolt pattern with a 72.6mm center bore. Factory wheels are F: 18x8.0J R: 18x8.0J.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the BMW 7-Series F01 (UK) (2009) we drill the 5x120 pattern and cut the centre bore to 72.6mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 10,093 vehicles, free to download, CC BY 4.0.
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 18x8.0J ET30 → ~5.68″ F backspacing, R 18x8.0J ET30 → ~5.68″ R backspacing
- Flush: F 19x8.5J ET20 → ~5.54″ F backspacing, R 19x9.5J ET25 → ~6.23″ R backspacing
- Max: F 20x9.0J ET18 → ~5.71″ F backspacing, R 20x10.0J ET22 → ~6.37″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact BMW spec, or want a wheel built to a custom offset for your BMW 7-Series F01 (UK)? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the BMW 7-Series F01 (UK) use?
The 2009 BMW 7-Series F01 (UK) uses a 5x120 bolt pattern.
How many lug bolts does the BMW 7-Series F01 (UK) use?
The BMW 7-Series F01 (UK) uses a 5-lug bolt pattern (5x120), so you need a 5-lug forged wheel to bolt straight on.
What is the center bore size on the BMW 7-Series F01 (UK)?
The BMW 7-Series F01 (UK)'s center bore is 72.6mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.
What size are the factory (stock) wheels on the BMW 7-Series F01 (UK)?
Factory wheels on the BMW 7-Series F01 (UK) are F: 18x8.0J R: 18x8.0J.
What is the biggest wheel size I can fit on my BMW 7-Series F01 (UK) without rubbing?
The most aggressive fitment we recommend without fender work is F 20x9.0J ET18 / R 20x10.0J ET22. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.
What does a flush wheel fitment look like on the BMW 7-Series F01 (UK)?
For a flush look with minimal to no rubbing, we recommend F 19x8.5J ET20 / R 19x9.5J ET25 as a starting point on a stock or mildly lowered BMW 7-Series F01 (UK).
Do I need wheel spacers for my BMW 7-Series F01 (UK)?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my BMW 7-Series F01 (UK)?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.54" backspacing up front and 6.23" in the rear.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my BMW 7-Series F01 (UK)?
Yes — the BMW 7-Series F01 (UK)'s factory and our recommended flush/max fitments already use staggered sizing (different width front and rear), and ANKUSI can forge matching staggered sets to your target offsets.
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.25, 60-degree conical-seat lug bolt.
Factory Torque Spec: 140 Nm (103 ft-lb). Consistent across modern BMW passenger and X-series models using factory conical-seat bolts.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.