← Fitment Guide · All Bentley Fitment Guides

2023 Bentley Bentayga EWB Wheels & Rims: Bolt Pattern, Offset & Sizes

Fitting Bentley Bentayga EWB wheels? This page gives the 2023 Bentley Bentayga EWB bolt pattern (5x130), centre bore, factory rim size and the offset range for aftermarket and forged Bentley Bentayga EWB rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.

Bentley Bentayga EWB (2023): 5x130 bolt pattern, 71.5mm center bore. Factory wheels: 21x9.0J F/R. Reference fitment ranges.

Bolt Pattern5x130

Wheel Bolt/NutM14x1.5 Bolt

Center Bore71.5mm

Wheel Load Rating900–1250 kg/wheel (SUV segment reference)

Caliper TypeBrembo multi-piston fixed caliper, front & rear (OEM, standard across Bentley Continental/Flying Spur lineup)

Year2023

CategoryLuxury SUV

✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →

Wheel Size & Offset at a Glance

Bentley Bentayga EWB wheel size and offset comparison by configuration
Configuration	Wheel Size & Offset
Factory (OE)	21x9.0J F/R
Flush Fitment	22x10.0J at ET25 offset
Maximum Aggressive	23x10.5J at ET20 offset

How to Read Wheel Offset & Measurements

Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.

Diagram showing wheel measurement points: centerline, center bore diameter, PCD, offset, rim width and diameter — Centerline, center bore, PCD, offset, width & diameter

Diagram comparing positive, zero, and negative wheel offset relative to the wheel centerline — Positive vs. zero vs. negative offset

ANKUSI Engineering Expert Advice

Because an SUV's center of gravity is already higher than a sedan's, anything added at the corners — including wheel weight — has an outsized effect on handling balance. A forged wheel lets us hit the visual stance owners want without adding the rotational mass a cast wheel of the same strength would carry.

The Bentley Bentayga EWB runs a 5x130 bolt pattern, 71.5mm center bore, and a 21x9.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 22x10.0J ET25, which tucks the tire under the fender lip on a stock-height Bentley Bentayga EWB. Our Maximum Aggressive reference is 23x10.5J ET20 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.

Bentley Bentayga EWB OE Wheel Specs

The 2023 Bentley Bentayga EWB (Luxury SUV) uses a 5x130 bolt pattern with a 71.5mm center bore. Factory wheels are 21x9.0J F/R.

Why the factory spec works for most owners:

Balances ride comfort with everyday drivability
A commonly used size for this vehicle class, supporting parts and tire availability
Maintains clearance for the factory suspension and brake components
Provides stable, predictable handling across normal driving conditions

ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Bentley Bentayga EWB (2023) we drill the 5x130 pattern and cut the centre bore to 71.5mm on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.

IATF 16949 & ISO 9001 certified · own 10,000-ton press in Guangzhou · from a single set to a full container

Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.

The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.

Get a quote for this car WhatsApp the factory

Flush Fitment

For a flush look with minimal rubbing, F/R 22x10.0J ET25 is the recommended starting point on a stock or mildly lowered Bentley Bentayga EWB.

Maximum Aggressive Fitment

F/R 23x10.5J ET20 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.

5-Tier Configuration Options

A Factory-Style 21x9.0J ET28

Recommended setup: 21x9.0J ET28 | Economy impact: Negligible | Best for: Daily commuting, family use

Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆

Estimated cost: $450-800 (wheels + tires + install)

B Comfortable Upgrade 22x9.5J ET27

Recommended setup: 22x9.5J ET27 | Economy impact: -2 to -4% | Best for: Daily / street

Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆

Estimated cost: $1,950-2,550 (wheels + tires + install)

C Balanced / Flush Fit 22x10.0J ET25

Recommended setup: 22x10.0J ET25 | Economy impact: -4 to -6% | Best for: Street

Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆

Estimated cost: $2,600-3,400 (wheels + tires + install)

D Aggressive 23x10.5J ET23

Recommended setup: 23x10.5J ET23 | Economy impact: -6 to -9% | Best for: Show / occasional track

Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆

Estimated cost: $3,900-5,000 (wheels + tires + install)

E Max Aggressive 23x10.5J ET20

Recommended setup: 23x10.5J ET20 | Economy impact: -8 to -12% | Best for: Show only

Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆

Estimated cost: $4,800-6,200+ (wheels + tires + install)

Performance Comparison Matrix

Metric	Tier A	Tier B	Tier C	Tier D	Tier E
Wheel Spec	21x9.0J ET28	22x9.5J ET27	22x10.0J ET25	23x10.5J ET23	23x10.5J ET20
Economy Impact	Negligible	-2 to -4%	-4 to -6%	-6 to -9%	-8 to -12%
Appearance	7/10	8/10	8.5/10	9/10	9.5/10
Comfort	9.5/10	9/10	8/10	6.5/10	4/10
Install Difficulty	★☆☆☆☆	★☆☆☆☆	★★☆☆☆	★★★☆☆	★★★★☆
Cost Range	$450-800	$1,950-2,550	$2,600-3,400	$3,900-5,000	$4,800-6,200+
Best For	Daily commuting, family use	Daily / street	Street	Show / occasional track	Show only

Real-World Reference Cases

The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.

Case 1: Daily Driver (Factory-Style)

Profile: Everyday driving, prioritizes comfort and low running cost.

Setup: 21x9.0J ET28

Cost: ~$620

Outcome: Minimal visual change, ride and fuel economy essentially unaffected.

Case 2: Balanced Enthusiast (Balanced / Flush Fit)

Profile: Wants a sportier stance without sacrificing daily usability.

Setup: 22x10.0J ET25

Cost: ~$3,000

Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.

Case 3: Show Build (Max Aggressive)

Profile: Built primarily for shows or occasional track/show use.

Setup: 23x10.5J ET20

Cost: ~$5,500

Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.

Decision Guide

What's your primary use? Daily commuting → Tier A/B. Weekend street driving → Tier B/C. Show or occasional track use → Tier D/E.

What's your budget? Under $800 → Tier A. $800-3,400 → Tier B/C. $3,400+ → Tier D/E.

How much does fuel economy matter? Very important → Tier A. Somewhat important → Tier B/C. Not a priority → Tier D/E.

Still unsure? Tier C (Balanced / Flush Fit) is the default choice for most Bentley Bentayga EWB owners.

Offset & Backspacing Reference

Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):

OE: 21x9.0J ET28 → ~6.1″ backspacing
Flush: 22x10.0J ET25 → ~6.48″ backspacing
Max: 23x10.5J ET20 → ~6.54″ backspacing

Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Bentley spec, or want a wheel built to a custom offset for your Bentley Bentayga EWB? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.

Custom Forged Wheels for the Bentley Bentayga EWB (2023)

Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.

Every set is cut to order, so the 5x130 pattern and the 71.5mm centre bore are machined for this car specifically rather than shimmed with adaptor rings. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose — most Bentley orders on this platform land somewhere between the 22x10.0J ET25 flush setup and the 23x10.5J ET20 aggressive setup referenced above.

Designs we already tool for the 5x130 pattern — each one is re-cut to your sizes and offsets:

Bentley OEM-Style Gloss Black Full-Face Forged Wheels – Bentley Bentayga / Flying Spur Fitment (5-Lug)

Bentley Continental GT / Bentayga Forged Wheels – Gloss Black Petal-Spoke Machined Face

Bentley Continental / Flying Spur Forged Wheels – Gloss Black Full-Face

Bentley Continental GT / Bentayga Forged Wheels – Silver 15-Spoke

Request a quote WhatsApp the factory Wholesale & OEM

Frequently Asked Questions

What bolt pattern (PCD) does the Bentley Bentayga EWB use?

The 2023 Bentley Bentayga EWB uses a 5x130 bolt pattern.

How many lug bolts does the Bentley Bentayga EWB use?

The Bentley Bentayga EWB uses a 5-lug bolt pattern (5x130), so you need a 5-lug forged wheel to bolt straight on.

What is the center bore size on the Bentley Bentayga EWB?

The Bentley Bentayga EWB's center bore is 71.5mm. If an aftermarket wheel has a larger center bore than this, hub-centric rings are recommended so the wheel centers on the hub itself rather than relying on the lug bolts alone.

What size are the factory (stock) wheels on the Bentley Bentayga EWB?

Factory wheels on the Bentley Bentayga EWB are 21x9.0J F/R.

What is the biggest wheel size I can fit on my Bentley Bentayga EWB without rubbing?

The most aggressive fitment we recommend without fender work is 23x10.5J at ET20 offset. Going beyond this typically causes rubbing under compression unless you roll the fenders or add camber correction.

What does a flush wheel fitment look like on the Bentley Bentayga EWB?

For a flush look with minimal to no rubbing, we recommend 22x10.0J at ET25 offset as a starting point on a stock or mildly lowered Bentley Bentayga EWB.

Do I need wheel spacers for my Bentley Bentayga EWB?

No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.

How do I calculate wheel backspacing for my Bentley Bentayga EWB?

Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 6.48" of backspacing.

What's the difference between wheel offset and backspacing?

Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.

Can I run staggered wheels (different sizes front and rear) on my Bentley Bentayga EWB?

The Bentley Bentayga EWB runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.

Forged Wheel Designs for the Bentley Bentayga EWB

Every design below is forged to order, so it can be machined to the Bentley Bentayga EWB's 5x130 bolt pattern and 71.5 mm center bore, with the width and offset calculated for your setup.