Opel Corsa Bolt Pattern, Center Bore & Wheel Offset (2007–2024)
Opel Corsa wheel fitment: 4x108 bolt pattern, 65.1mm center bore; 4x100 bolt pattern, 56.6mm center bore. OE wheel sizes and offsets for every Corsa variant w
- 4x108bolt pattern (PCD), most common
- 65.1 mmcenter bore
- M12x1.5 Nutwheel bolt / nut
- 2 guidesmodel years 2007–2024
Bolt pattern by generation
- 4x108, 65.1 mm center bore — 2024 (1 variants)
- 4x100, 56.6 mm center bore — 2007 (1 variants)
Opel Corsa wheel specs by year and trim
| Year | Model / trim | Bolt pattern | Center bore | OE wheel |
|---|---|---|---|---|
| 2024 | Opel Corsa | 4x108 | 65.1 mm | 17x7J ET32 |
| 2007 | Opel Corsa 5-door | 4x100 | 56.6 mm | 15x6J ET39 |
Factory wheel sizes on the Opel Corsa
Across the 2 Opel Corsa trims with a documented factory wheel, the OE diameter is 15-17 inch, width 6-7J and offset ET32-39. A forged wheel that keeps the bolt pattern and hub bore of your generation (see the table above) and stays inside that offset range bolts on without spacers or hub rings. Going one inch up in diameter with a lower-profile tyre keeps the rolling circumference inside the usual 1.5% tolerance; every extra 0.5J of width moves the outer lip about 6 mm outward at the same offset, and each 5 mm less offset moves the whole wheel 5 mm outward.
Forged wheels for the Opel Corsa (4x108)
Shop all Opel Corsa forged wheels →
Get a quote for Opel Corsa wheels
Vehicles With the Same Hub as the Opel Corsa (4x108, 65.1 mm Bore)
In our database, 111 other vehicle entries from 10 makes use exactly the same 4x108 bolt pattern and 65.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
4x108 is used by 2.6% of the vehicle entries in our database (169 of 6,503); 72.2% of those also use a 65.1 mm center bore.
Offset and Backspacing: Factory Wheel vs Options
Backspacing ≈ width/2 + ET/25.4 + 0.5 in. "Inward" means closer to the suspension; "outward" means closer to the fender lip.
| Setup | Size | ET | Backspacing | Inward vs OE | Outward vs OE |
|---|---|---|---|---|---|
| Factory (OE) | 17x7J | ET32 | 5.26 in (134 mm) | — | — |
| Flush | 18x7.5J | ET25 | 5.23 in (133 mm) | −1 mm | +13 mm |
| Maximum | 18x8J | ET20 | 5.29 in (134 mm) | +1 mm | +25 mm |
Hub-Centric Rings for a 65.1 mm Center Bore
A wheel with a center bore larger than 65.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 66.1 mm | 66.1 → 65.1 mm |
| 66.6 mm | 66.6 → 65.1 mm |
| 67.1 mm | 67.1 → 65.1 mm |
| 70.1 mm | 70.1 → 65.1 mm |
| 73.1 mm | 73.1 → 65.1 mm |
ANKUSI forged wheels are bored to exactly 65.1 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.
FAQ
What is the bolt pattern on a Opel Corsa?
The Opel Corsa uses a 4x108 bolt pattern on most variants we cover with a 65.1mm center bore. Other generations use 4x100 / 56.6mm (2007–2007). Always check the exact year and trim before ordering.
What is the Opel Corsa center bore?
The hub-centric center bore is 65.1 mm on the most common generation; see the table for variants. Aftermarket wheels should match this bore or use hub-centric rings so the hub, not the bolts, carries the load.
Do all Opel Corsa years share the same wheel fitment?
No. The bolt pattern or center bore changed between generations, so wheels are not interchangeable across all years. Use the year-by-year table on this page to pick the right specification.
Which forged wheels fit the Opel Corsa?
Any wheel drilled 4x108 with a 65.1mm hub bore in the offset range shown on the model guide. ANKUSI forges wheels to order for this exact specification, in 14–24 inch diameters, so no adapters or hub rings are needed.