2020 Cupra Leon Competicion Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Cupra Leon Competicion wheels? This page gives the 2020 Cupra Leon Competicion bolt pattern, centre bore, factory rim size and the offset range for aftermarket and forged Cupra Leon Competicion rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Quick answer: The 2020 Cupra Leon Competicion uses a 5x112 bolt pattern with a 57.1 mm centre bore and M14x1.5 lug bolts.
Forged wheels for the 2020 Cupra Leon Competicion — drilled 5x112 with a 57.1 mm centre bore, built to the offset you choose. From $220 per wheel, made to order in 20–25 days.
Get a quote for this car
Cupra Leon Competicion (2020): 18x10.0J F/R on a 5*112 hub. Competition/one-off vehicle -- no aftermarket data published.
✓ Data check: the bolt pattern and center bore on this page match an independent fitment reference. Last reviewed September 18, 2026. How we verify
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Competition and prototype hubs are built to a specific series' or shop's homologation rules, not to a retail bolt pattern, so there's no generic 'Flush' or 'Maximum Aggressive' range that means anything here. What forging does contribute is unsprung mass reduction at the exact same structural rating the homologated spec requires — a real, measurable gain in a discipline where every gram of rotational inertia is fought for.
The Cupra Leon Competicion runs 18x10.0J F/R on a homologated racing hub, not a standard retail bolt pattern. ANKUSI's motorsport program forges to this exact homologated specification rather than offering generic Flush or Maximum Aggressive references, which would be meaningless on a hub this specialized — contact us with your series or application's exact hub requirements.
Cupra Leon Competicion Wheel & Hub Specs
The 2020 Cupra Leon Competicion (GT / Cup Race Car) runs 18x10.0J F/R on a 5*112 homologated bolt pattern. These are the factory or homologated racing specifications, not a standard retail bolt pattern.
Why We Don't Publish Generic Aftermarket Fitment for This Vehicle
The Cupra Leon Competicion is a competition, prototype, vintage or one-off commissioned vehicle. Unlike a mass-produced road car, there is no generic enthusiast community publishing "Flush" or "Maximum Aggressive" offset ranges for it, and its hub is homologated to a specific racing application. Publishing invented offset numbers for a car like this would be misleading, so we don't.
Custom & Motorsport Wheel Program
ANKUSI forges wheels to exact motorsport specifications -- centerlock, beadlock, homologation-compliant, restoration-correct, or one-off replica builds. Contact ANKUSI with your exact hub pattern, offset and application and we will confirm whether we can build for it.
Vehicles With the Same Hub as the Cupra Leon Competicion (5x112, 57.1 mm Bore)
In our database, 407 other vehicle entries from 18 makes use exactly the same 5x112 bolt pattern and 57.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x112 is used by 21.6% of the vehicle pages in our English fitment guide (1,407 of 6,503); 29.0% of those also use a 57.1 mm center bore.
Hub-Centric Rings for a 57.1 mm Center Bore
A wheel with a center bore larger than 57.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 60.1 mm | 60.1 → 57.1 mm |
| 63.4 mm | 63.4 → 57.1 mm |
| 64.1 mm | 64.1 → 57.1 mm |
| 65.1 mm | 65.1 → 57.1 mm |
| 73.1 mm | 73.1 → 57.1 mm |
ANKUSI forged wheels are bored to exactly 57.1 mm for this vehicle, so no ring is needed.
Frequently Asked Questions
Does the Cupra Leon Competicion use a standard bolt pattern?
No. It uses a 5*112 homologated bolt pattern, not a retail lug-bolt pattern, so off-the-shelf aftermarket road wheels do not apply.
Can ANKUSI build wheels for a Cupra Leon Competicion?
Yes, on a custom-quote basis for restoration, motorsport or replica applications. Contact us with your exact specifications.
Why isn't there a Flush/Max fitment guide for this car?
Flush and Maximum Aggressive figures on our other pages come from verified enthusiast community data for mass-produced road cars. No such generic data exists for this vehicle, so we don't fabricate it.
Sources and Last Update
Data checked against: avtoreference.com.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.