Mercedes-Benz C220 CDI Avantgarde (2004) Wheel Fitment
Mercedes-Benz C220 CDI Avantgarde (2004): 5x112 bolt pattern, 66.6mm center bore. Factory wheels: 16x7.0J F/R. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | 16x7.0J F/R |
| Flush Fitment | 17x7.5J at ET35 offset |
| Maximum Aggressive | 18x8.0J at ET32 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
Wagons split the difference between sedan agility and load-carrying duty, and the wheels have to serve both roles. A forged wheel holds the same structural margin as the factory piece while trimming rotational weight, which benefits both the empty-car handling and the loaded-car ride.
The Mercedes-Benz C220 CDI Avantgarde runs a 5x112 bolt pattern, 66.6mm center bore, and a 16x7.0J, front and rear, wheel from the factory. Our Flush Fitment reference is 17x7.5J ET35, which tucks the tire under the fender lip on a stock-height Mercedes-Benz C220 CDI Avantgarde. Our Maximum Aggressive reference is 18x8.0J ET32 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Mercedes-Benz C220 CDI Avantgarde OE Wheel Specs
The 2004 Mercedes-Benz C220 CDI Avantgarde (Diesel Sedan) uses a 5x112 bolt pattern with a 66.6mm center bore. Factory wheels are 16x7.0J F/R.
Why the factory spec works for most owners:
- Balances ride comfort with everyday fuel efficiency
- A widely used size in this segment, so tire and wheel availability stays strong
- Keeps unsprung weight low for stable, predictable handling
- Maintains clearance for the factory brake calipers and suspension components
Flush Fitment
For a flush look with minimal rubbing, F/R 17x7.5J ET35 is the recommended starting point on a stock or mildly lowered Mercedes-Benz C220 CDI Avantgarde.
Maximum Aggressive Fitment
F/R 18x8.0J ET32 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style 16x7.0J ET37
Recommended setup: 16x7.0J ET37 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade 17x7.5J ET36
Recommended setup: 17x7.5J ET36 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit 17x7.5J ET35
Recommended setup: 17x7.5J ET35 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive 18x8.0J ET34
Recommended setup: 18x8.0J ET34 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive 18x8.0J ET32
Recommended setup: 18x8.0J ET32 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 16x7.0J ET37 | 17x7.5J ET36 | 17x7.5J ET35 | 18x8.0J ET34 | 18x8.0J ET32 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: 16x7.0J ET37
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: 17x7.5J ET35
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: 18x8.0J ET32
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: 16x7.0J ET37 → ~5.46″ backspacing
- Flush: 17x7.5J ET35 → ~5.63″ backspacing
- Max: 18x8.0J ET32 → ~5.76″ backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Mercedes-Benz spec, or want a wheel built to a custom offset for your Mercedes-Benz C220 CDI Avantgarde? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Mercedes-Benz C220 CDI Avantgarde use?
How many lug bolts does the Mercedes-Benz C220 CDI Avantgarde use?
What is the center bore size on the Mercedes-Benz C220 CDI Avantgarde?
What size are the factory (stock) wheels on the Mercedes-Benz C220 CDI Avantgarde?
What is the biggest wheel size I can fit on my Mercedes-Benz C220 CDI Avantgarde without rubbing?
What does a flush wheel fitment look like on the Mercedes-Benz C220 CDI Avantgarde?
Do I need wheel spacers for my Mercedes-Benz C220 CDI Avantgarde?
How do I calculate wheel backspacing for my Mercedes-Benz C220 CDI Avantgarde?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Mercedes-Benz C220 CDI Avantgarde?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M14x1.5, ball-seat lug bolt.
Factory Torque Spec: 130 Nm (96 ft-lb). Sedan/coupe platforms (E-Class, CLS, SL and similar) generally use the shorter 27mm bolt at this spec.
TPMS: Vehicles built before the 2008 model year were not federally required to carry factory TPMS in the US, though many manufacturers adopted it earlier; verify whether your specific build has TPMS before ordering sensor-compatible wheels.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.