Tenet Wheel Fitment Guide
3 fitment guides for Tenet, covering the 2026 model year, built around the 5x108 bolt pattern. Browse the full list below, then open a model for bolt pattern, center bore, OE offset, flush and max wheel sizes, and offset/backspacing conversions.
Tenet Bolt Pattern & Center Bore Notes
Based on the 3 Tenet fitment guides we cover, we have documented 2 distinct bolt pattern / center bore combinations across different Tenet platforms and model years:
- 5x108 bolt pattern, 60.1mm center bore — 2 models we cover, spanning 2026.
- 5x108 bolt pattern, 65.1mm center bore — 1 model we cover, spanning 2026.
Do not mix platforms: a wheel forged for one Tenet bolt pattern / center bore combination will not hub-center correctly on a different one, even if the diameter looks right. Always confirm your exact model and year against the bolt pattern and center bore listed on that model page below before ordering — or send us your VIN or trim level and we will confirm it for you.
Offset and backspacing recommendations vary by trim even within the same bolt pattern, mainly due to differences in brake caliper size and suspension geometry between base and performance trims. Every ANKUSI wheel is forged to your exact target offset, so send us your Tenet model, year, and trim and we will confirm the correct spec before production — no guessing required.
How to check the bolt pattern on your Tenet
The most common Tenet fitment in our guide is 5x108 with a 60.1 mm center bore (2 of 3 model years we cover).
- Read the stamping on the back of an original wheel: size, offset (ET) and bolt pattern are usually cast into a spoke or the hub pad.
- No stamping? Measure center-to-center between two adjacent lug holes. For 5x108 that distance is 63.5 mm (PCD × sin(180° / 5)). A 2 mm difference already means a different bolt pattern.
- Match generation and year on the model pages below — the same nameplate can change bolt pattern or center bore between generations.
Changing width or offset? Check how far the wheel moves in or out with our offset & backspacing calculator.
5x108 / 60.1mm center bore
5x108 / 65.1mm center bore
Vehicles Using 5x108 With a 60.1 mm Center Bore
In our database, 60 other vehicle entries from 10 makes use exactly the same 5x108 bolt pattern and 60.1 mm center bore. Factory wheels from these cars bolt on and center on the hub without rings; offset and width still have to be checked.
5x108 is used by 7.7% of the vehicle entries in our database (498 of 6,503); 12.4% of those also use a 60.1 mm center bore.
Hub-Centric Rings for a 60.1 mm Center Bore
A wheel with a center bore larger than 60.1 mm needs a hub-centric ring. The most common combinations:
| Wheel bore | Ring size |
|---|---|
| 63.4 mm | 63.4 → 60.1 mm |
| 64.1 mm | 64.1 → 60.1 mm |
| 65.1 mm | 65.1 → 60.1 mm |
| 66.1 mm | 66.1 → 60.1 mm |
| 73.1 mm | 73.1 → 60.1 mm |
ANKUSI forged wheels are bored to exactly 60.1 mm for this vehicle, so no ring is needed.
Sources and Last Update
Bolt pattern and center bore were checked against at least two independent fitment references before publication.
This record is part of the open ANKUSI Wheel Fitment Dataset (DOI 10.5281/zenodo.23241521, CC BY 4.0).
Compiled by the ANKUSI Wheels engineering team, an IATF 16949 and ISO 9001 certified forged wheel factory in Guangzhou.