Larte Design Larte Range Rover Sport Winner (2015) Wheel Fitment
Larte Design Larte Range Rover Sport Winner (2015): 5x120 bolt pattern, 72.6mm center bore, OE 22x9.5J ET45. Forged wheel fitment specs from ANKUSI.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | 22x10.5J at ET35 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
SUVs carry more curb weight higher off the ground, so wheel strength and rotational mass both matter more than on a comparable sedan — a heavier wheel amplifies body roll and slows steering response exactly where the platform is already working hardest. Forging keeps the wheel light without giving up the load rating the factory suspension geometry was tuned around.
The Larte Design Larte Range Rover Sport Winner ships from the factory on a 5x120 bolt pattern with a 72.6mm center bore and a 22x9.5J ET45 wheel. Our flush reference for the Larte Design Larte Range Rover Sport Winner is 22x10.5J ET35.; our maximum aggressive reference is 24x10J ET30. — beyond that, expect clearance issues against the fender liner without further modification.
Larte Design Larte Range Rover Sport Winner OE Wheel Specs
The Larte Design Larte Range Rover Sport Winner ships from the factory on 5x120 bolt pattern wheels with a 72.6mm center bore. The stock wheel size is 22x9.5J ET45, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
Flush Fitment
For a flush look without any body modification, most Larte Design Larte Range Rover Sport Winner owners run 22x10.5J ET35. This setup tucks the wheel face closer to the fender lip while staying within safe load and clearance limits.
Maximum Aggressive Fitment
Owners chasing a more aggressive stance push to 24x10J ET30. Chassis: Air suspension lowering links. Wheels: Requires high load rating. Larte kits typically feature aggressive styling that can accommodate larger diameter wheels. Brakes: Large front caliper clearance needed. Tires: 275/40 R22 or 285/40 R22. Clearance should be verified before ordering, especially on lowered cars.
5-Tier Configuration Options
A – Factory-Style: 22x9.5J ET45
Recommended setup: Factory-matched forged replacement
Economy impact: None
Best for: Daily drivers, warranty-conscious owners
Appearance 5/10 | Comfort 10/10 | Install difficulty ★☆☆☆
Estimated cost range: $$ (OE replacement)
B – Comfortable Upgrade: 22x10J ET40
Recommended setup: Direct bolt-on, factory suspension
Economy impact: Minimal
Best for: Owners who want a mild upgrade with no compromise
Appearance 6/10 | Comfort 9/10 | Install difficulty ★☆☆☆
Estimated cost range: $$ - $$$
C – Balanced / Flush Fit: 22x10.5J ET35
Recommended setup: Flush forged wheels, stock or mild lowering
Economy impact: Slight increase
Best for: Enthusiasts wanting a flush look daily
Appearance 8/10 | Comfort 7/10 | Install difficulty ★★☆☆
Estimated cost range: $$$
D – Aggressive: 23x10.5J ET33
Recommended setup: Wider forged wheels, coilovers or lowering springs
Economy impact: Noticeable increase
Best for: Show-and-drive builds
Appearance 9/10 | Comfort 5/10 | Install difficulty ★★★☆
Estimated cost range: $$$$
E – Max Aggressive: 24x10J ET30
Recommended setup: Chassis: Air suspension lowering links. Wheels: Requires high load rating. Larte kits typically feature aggressive styling that can accommodate larger diameter wheels. Brakes: Large front caliper clearance needed. Tires: 275/40 R22 or 285/40 R22.
Economy impact: Significant increase
Best for: Show builds, weekend cars
Appearance 10/10 | Comfort 3/10 | Install difficulty ★★★★
Estimated cost range: $$$$$
Performance Comparison Matrix
| Wheel Spec | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 22x9.5J ET45 | 22x10J ET40 | 22x10.5J ET35 | 23x10.5J ET33 | 24x10J ET30 |
| Economy Impact | None | Minimal | Slight increase | Noticeable increase | Significant increase |
| Appearance | 5/10 | 6/10 | 8/10 | 9/10 | 10/10 |
| Comfort | 10/10 | 9/10 | 7/10 | 5/10 | 3/10 |
| Install Difficulty | ★☆☆☆ | ★☆☆☆ | ★★☆☆ | ★★★☆ | ★★★★ |
| Cost Range | $$ (OE replacement) | $$ - $$$ | $$$ | $$$$ | $$$$$ |
| Best For | Daily drivers, warranty-conscious owners | Owners who want a mild upgrade with no compromise | Enthusiasts wanting a flush look daily | Show-and-drive builds | Show builds, weekend cars |
Real-World Reference Cases
The following builds are compiled from typical ANKUSI customer configurations for this platform and are illustrative, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Commuter prioritizing comfort and reliability.
Setup: 22x9.5J ET45 forged wheels, factory suspension.
Cost: $$ (OE replacement)
Outcome: No clearance issues, factory ride quality retained.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Weekend driver wanting a flush stance without sacrificing daily usability.
Setup: 22x10.5J ET35 forged wheels, mild lowering springs.
Cost: $$$
Outcome: Flush fitment with acceptable ride comfort for daily use.
Case 3: Show Build (Max Aggressive)
Profile: Show-and-shine build prioritizing stance over comfort.
Setup: 24x10J ET30 forged wheels. Chassis: Air suspension lowering links. Wheels: Requires high load rating. Larte kits typically feature aggressive styling that can accommodate larger diameter wheels. Brakes: Large front caliper clearance needed. Tires: 275/40 R22 or 285/40 R22.
Cost: $$$$$
Outcome: Maximum aggressive stance; clearance verified case-by-case.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 22x9.5J ET45: backspacing ≈ 7.02"
- Flush 22x10.5J ET35: backspacing ≈ 7.13"
- Max 24x10J ET30: backspacing ≈ 6.68"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Larte Design Larte Range Rover Sport Winner.