Ford Mustang Shelby GT-H (2016) Wheel Fitment
Ford Mustang Shelby GT-H (2016): 5x114.3 bolt pattern, 70.5mm center bore. Factory wheels: F: 19x9.0J R: 19x9.5J. Reference fitment ranges.
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Factory (OE) | F: 19x9.0J R: 19x9.5J |
| Flush Fitment | F 20x9.5J ET35 / R 20x10.5J ET40 |
| Maximum Aggressive | F 20x10.0J ET30 / R 21x11.0J ET35 |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
The Ford Mustang Shelby GT-H's chassis tuning assumes a certain amount of rotational mass at each corner. Forging lets ANKUSI cut that mass while matching the factory strength rating, which sharpens turn-in and reduces the energy the brakes have to absorb — a real gain on a coupe platform, not just a styling change.
The Ford Mustang Shelby GT-H runs a 5x114.3 bolt pattern, 70.5mm center bore, and a F: 19x9.0J wheel from the factory. Our Flush Fitment reference is F 20x9.5J ET35 / R 20x10.5J ET40, which tucks the tire under the fender lip on a stock-height Ford Mustang Shelby GT-H. Our Maximum Aggressive reference is F 20x10.0J ET30 / R 21x11.0J ET35 — beyond that offset, expect rubbing against the inner fender liner under compression without further trimming.
Ford Mustang Shelby GT-H OE Wheel Specs
The 2016 Ford Mustang Shelby GT-H (Coupe) uses a 5x114.3 bolt pattern with a 70.5mm center bore. Factory wheels are F: 19x9.0J R: 19x9.5J.
Why the factory spec works for most owners:
- Keeps the factory ride quality and noise levels intact
- A common fitment for this class, so replacement tires are easy to source
- Preserves clearance around the OE brakes and suspension geometry
- Delivers predictable, easy-to-live-with handling for daily use
Flush Fitment
For a flush look with minimal rubbing, F 20x9.5J ET35 / R 20x10.5J ET40 is the recommended starting point on a stock or mildly lowered Ford Mustang Shelby GT-H.
Maximum Aggressive Fitment
F 20x10.0J ET30 / R 21x11.0J ET35 is a more aggressive reference setup. Beyond this, expect rubbing under compression without fender rolling or camber correction.
5-Tier Configuration Options
A Factory-Style F 19x9.0J ET45 / R 19x9.5J ET52
Recommended setup: F 19x9.0J ET45 / R 19x9.5J ET52 | Economy impact: Negligible | Best for: Daily commuting, family use
Appearance: 7/10 | Comfort: 9.5/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $450-800 (wheels + tires + install)
B Comfortable Upgrade F 20x9.5J ET40 / R 20x10.0J ET46
Recommended setup: F 20x9.5J ET40 / R 20x10.0J ET46 | Economy impact: -2 to -4% | Best for: Daily / street
Appearance: 8/10 | Comfort: 9/10 | Install difficulty: ★☆☆☆☆
Estimated cost: $1,950-2,550 (wheels + tires + install)
C Balanced / Flush Fit F 20x9.5J ET35 / R 20x10.5J ET40
Recommended setup: F 20x9.5J ET35 / R 20x10.5J ET40 | Economy impact: -4 to -6% | Best for: Street
Appearance: 8.5/10 | Comfort: 8/10 | Install difficulty: ★★☆☆☆
Estimated cost: $2,600-3,400 (wheels + tires + install)
D Aggressive F 20x10.0J ET33 / R 21x11.0J ET38
Recommended setup: F 20x10.0J ET33 / R 21x11.0J ET38 | Economy impact: -6 to -9% | Best for: Show / occasional track
Appearance: 9/10 | Comfort: 6.5/10 | Install difficulty: ★★★☆☆
Estimated cost: $3,900-5,000 (wheels + tires + install)
E Max Aggressive F 20x10.0J ET30 / R 21x11.0J ET35
Recommended setup: F 20x10.0J ET30 / R 21x11.0J ET35 | Economy impact: -8 to -12% | Best for: Show only
Appearance: 9.5/10 | Comfort: 4/10 | Install difficulty: ★★★★☆
Estimated cost: $4,800-6,200+ (wheels + tires + install)
Performance Comparison Matrix
| Metric | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | F 19x9.0J ET45 / R 19x9.5J ET52 | F 20x9.5J ET40 / R 20x10.0J ET46 | F 20x9.5J ET35 / R 20x10.5J ET40 | F 20x10.0J ET33 / R 21x11.0J ET38 | F 20x10.0J ET30 / R 21x11.0J ET35 |
| Economy Impact | Negligible | -2 to -4% | -4 to -6% | -6 to -9% | -8 to -12% |
| Appearance | 7/10 | 8/10 | 8.5/10 | 9/10 | 9.5/10 |
| Comfort | 9.5/10 | 9/10 | 8/10 | 6.5/10 | 4/10 |
| Install Difficulty | ★☆☆☆☆ | ★☆☆☆☆ | ★★☆☆☆ | ★★★☆☆ | ★★★★☆ |
| Cost Range | $450-800 | $1,950-2,550 | $2,600-3,400 | $3,900-5,000 | $4,800-6,200+ |
| Best For | Daily commuting, family use | Daily / street | Street | Show / occasional track | Show only |
Real-World Reference Cases
The examples below are compiled from typical ANKUSI customer configurations and are labeled as reference cases, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Everyday driving, prioritizes comfort and low running cost.
Setup: F 19x9.0J ET45 / R 19x9.5J ET52
Cost: ~$620
Outcome: Minimal visual change, ride and fuel economy essentially unaffected.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Wants a sportier stance without sacrificing daily usability.
Setup: F 20x9.5J ET35 / R 20x10.5J ET40
Cost: ~$3,000
Outcome: Noticeable visual upgrade, fuel economy drop within the expected range.
Case 3: Show Build (Max Aggressive)
Profile: Built primarily for shows or occasional track/show use.
Setup: F 20x10.0J ET30 / R 21x11.0J ET35
Cost: ~$5,500
Outcome: Maximum visual impact; daily comfort and fuel economy are heavily compromised, physical test fit required before production.
Decision Guide
Offset & Backspacing Reference
Backspacing is calculated as wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance):
- OE: F 19x9.0J ET45 → ~6.77″ F backspacing, R 19x9.5J ET52.5 → ~7.32″ R backspacing
- Flush: F 20x9.5J ET35 → ~6.63″ F backspacing, R 20x10.5J ET40 → ~7.32″ R backspacing
- Max: F 20x10.0J ET30 → ~6.68″ F backspacing, R 21x11.0J ET35 → ~7.38″ R backspacing
Want to check a different width or offset before you order? Use our Offset & Backspacing Calculator to solve the numbers yourself, or looking for your exact Ford spec, or want a wheel built to a custom offset for your Ford Mustang Shelby GT-H? Contact ANKUSI with your bolt pattern and offset target and we will confirm the correct forged wheel spec for your build.
Frequently Asked Questions
What bolt pattern (PCD) does the Ford Mustang Shelby GT-H use?
How many lug bolts does the Ford Mustang Shelby GT-H use?
What is the center bore size on the Ford Mustang Shelby GT-H?
What size are the factory (stock) wheels on the Ford Mustang Shelby GT-H?
What is the biggest wheel size I can fit on my Ford Mustang Shelby GT-H without rubbing?
What does a flush wheel fitment look like on the Ford Mustang Shelby GT-H?
Do I need wheel spacers for my Ford Mustang Shelby GT-H?
How do I calculate wheel backspacing for my Ford Mustang Shelby GT-H?
What's the difference between wheel offset and backspacing?
Can I run staggered wheels (different sizes front and rear) on my Ford Mustang Shelby GT-H?
Wheel Installation Reference: Torque, Thread & TPMS
Thread & Fastener: M12x1.5, conical-seat lug nut.
Factory Torque Spec: 136 Nm (100 ft-lb). Covers most Ford passenger cars and crossovers (Fusion, Focus, Escape and similar) on M12x1.5 studs.
TPMS: TPMS (Tire Pressure Monitoring System) has been federally mandated on all new light vehicles sold in the US since the 2008 model year. If your wheels use OE-style sensors, have them transferred or cloned to the new wheels at installation.
Tire Pressure: Always set tire pressure to the value on your vehicle's tire placard (driver's doorjamb or glovebox), not the max PSI printed on the tire sidewall — this is trim- and tire-size-specific and stays the same reference point when you switch to a different wheel and tire combination.
Reference data compiled from published OEM service specifications and cross-checked against independent repair sources; always confirm against your owner's manual or door-jamb placard before installation.