Skoda OEM-Style Gloss Black Machined Face Forged Wheels
Skoda Yeti / Octavia Combi 4×4 Fitment · 5-Lug
2020 Skoda Rapid [RU] Wheels & Rims: Bolt Pattern, Offset & Sizes
Fitting Skoda Rapid [RU] wheels? This page gives the 2020 Skoda Rapid [RU] bolt pattern (5x100), centre bore, factory rim size and the offset range for aftermarket and forged Skoda Rapid [RU] rims: the same spec sheet ANKUSI uses when machining forged wheels for this car.
Skoda Rapid [RU] (2020): 5x100 bolt pattern, 57.1mm center bore, OE 16x6J ET38. Forged wheel fitment specs from ANKUSI.
Bolt Pattern5x100
Wheel Bolt/NutM14x1.5 Bolt
Center Bore57.1mm
Wheel Load Rating650–750 kg/wheel (Standard Passenger Car segment reference)
Year2020
Category5-Lug Standard Sedan
✓ Verified by ANKUSI's Engineering Team — IATF 16949 & ISO 9001 certified forged wheel manufacturer, TÜV/SFI/VIA compliant. See our factory & certifications →
Wheel Size & Offset at a Glance
| Configuration | Wheel Size & Offset |
|---|---|
| Flush Fitment | 17x7.5J at ET32 offset |
How to Read Wheel Offset & Measurements
Use these two references before ordering: the left diagram shows where each spec (PCD, center bore, offset, width and diameter) is measured on the wheel; the right diagram shows how positive, zero and negative offset shift the wheel face relative to the hub centerline.
ANKUSI Engineering Expert Advice
A sedan's wheel spec is a balance point the factory tuned between ride comfort, steering feel, and everyday durability. Forging lets us hold that same structural margin while cutting rotational mass, which is where most of the real-world benefit — quicker steering response, marginally better ride — actually comes from.
The Skoda Rapid [RU] ships from the factory on a 5x100 bolt pattern with a 57.1mm center bore and a 16x6J ET38 wheel. Our flush reference for the Skoda Rapid [RU] is 17x7.5J ET32.; our maximum aggressive reference is 17x8J ET28. — beyond that, expect clearance issues against the fender liner without further modification.
Skoda Rapid [RU] OE Wheel Specs
The Skoda Rapid [RU] ships from the factory on 5x100 bolt pattern wheels with a 57.1mm center bore. The stock wheel size is 16x6J ET38, offering a balanced ride that suits most owners without any rubbing or clearance concerns.
Why the factory spec works for most owners:
- Balances ride comfort with steering response and highway efficiency.
- Wide tire and wheel availability at the factory diameter keeps replacement costs low.
- Lower unsprung weight than larger aftermarket wheels helps ride quality and acceleration.
- Guaranteed clearance against brake calipers and suspension components.
ANKUSI builds these wheels — we are the forging factory, not a reseller. For the Skoda Rapid [RU] (2020) we drill the 5x100 pattern on our own CNC line, so the wheel hub-centres on the car with no spacer rings, in whatever diameter, width and offset you specify.
Converting these ET figures to backspacing? Use the wheel offset and backspacing calculator.
The figures on this page are part of our open wheel fitment dataset — 6,436 vehicles, free to download, CC BY 4.0.
Flush Fitment
For a flush look without any body modification, most Skoda Rapid [RU] owners run 17x7.5J ET32. This setup tucks the wheel face closer to the fender lip while staying within safe load and clearance limits.
Maximum Aggressive Fitment
Owners chasing a more aggressive stance push to 17x8J ET28. Tein Street Advance Z coilovers; 17x7.5J ET32 ENKEI RPF1 wheels; EBC Greenstuff pads; Michelin Pilot Sport 4 205/45 R17 tires. Note: Second-gen Rapid redesign for Russia/CIS markets (PQ26 platform). Clearance should be verified before ordering, especially on lowered cars.
5-Tier Configuration Options
A – Factory-Style: 16x6J ET38
Recommended setup: Factory-matched forged replacement
Economy impact: None
Best for: Daily drivers, warranty-conscious owners
Appearance 5/10 | Comfort 10/10 | Install difficulty ★☆☆☆
Estimated cost range: $$ (OE replacement)
B – Comfortable Upgrade: 16.5x7J ET35
Recommended setup: Direct bolt-on, factory suspension
Economy impact: Minimal
Best for: Owners who want a mild upgrade with no compromise
Appearance 6/10 | Comfort 9/10 | Install difficulty ★☆☆☆
Estimated cost range: $$ - $$$
C – Balanced / Flush Fit: 17x7.5J ET32
Recommended setup: Flush forged wheels, stock or mild lowering
Economy impact: Slight increase
Best for: Enthusiasts wanting a flush look daily
Appearance 8/10 | Comfort 7/10 | Install difficulty ★★☆☆
Estimated cost range: $$$
D – Aggressive: 17x8J ET30
Recommended setup: Wider forged wheels, coilovers or lowering springs
Economy impact: Noticeable increase
Best for: Show-and-drive builds
Appearance 9/10 | Comfort 5/10 | Install difficulty ★★★☆
Estimated cost range: $$$$
E – Max Aggressive: 17x8J ET28
Recommended setup: Tein Street Advance Z coilovers; 17x7.5J ET32 ENKEI RPF1 wheels; EBC Greenstuff pads; Michelin Pilot Sport 4 205/45 R17 tires. Note: Second-gen Rapid redesign for Russia/CIS markets (PQ26 platform).
Economy impact: Significant increase
Best for: Show builds, weekend cars
Appearance 10/10 | Comfort 3/10 | Install difficulty ★★★★
Estimated cost range: $$$$$
Performance Comparison Matrix
| Wheel Spec | Tier A | Tier B | Tier C | Tier D | Tier E |
|---|---|---|---|---|---|
| Wheel Spec | 16x6J ET38 | 16.5x7J ET35 | 17x7.5J ET32 | 17x8J ET30 | 17x8J ET28 |
| Economy Impact | None | Minimal | Slight increase | Noticeable increase | Significant increase |
| Appearance | 5/10 | 6/10 | 8/10 | 9/10 | 10/10 |
| Comfort | 10/10 | 9/10 | 7/10 | 5/10 | 3/10 |
| Install Difficulty | ★☆☆☆ | ★☆☆☆ | ★★☆☆ | ★★★☆ | ★★★★ |
| Cost Range | $$ (OE replacement) | $$ - $$$ | $$$ | $$$$ | $$$$$ |
| Best For | Daily drivers, warranty-conscious owners | Owners who want a mild upgrade with no compromise | Enthusiasts wanting a flush look daily | Show-and-drive builds | Show builds, weekend cars |
Real-World Reference Cases
The following builds are compiled from typical ANKUSI customer configurations for this platform and are illustrative, not individually verified real-world builds.
Case 1: Daily Driver (Factory-Style)
Profile: Commuter prioritizing comfort and reliability.
Setup: 16x6J ET38 forged wheels, factory suspension.
Cost: $$ (OE replacement)
Outcome: No clearance issues, factory ride quality retained.
Case 2: Balanced Enthusiast (Balanced / Flush Fit)
Profile: Weekend driver wanting a flush stance without sacrificing daily usability.
Setup: 17x7.5J ET32 forged wheels, mild lowering springs.
Cost: $$$
Outcome: Flush fitment with acceptable ride comfort for daily use.
Case 3: Show Build (Max Aggressive)
Profile: Show-and-shine build prioritizing stance over comfort.
Setup: 17x8J ET28 forged wheels. Tein Street Advance Z coilovers; 17x7.5J ET32 ENKEI RPF1 wheels; EBC Greenstuff pads; Michelin Pilot Sport 4 205/45 R17 tires. Note: Second-gen Rapid redesign for Russia/CIS markets (PQ26 platform).
Cost: $$$$$
Outcome: Maximum aggressive stance; clearance verified case-by-case.
Decision Guide
1. What is this car mainly used for? Daily driving favors Tier A or B; weekend/show use favors Tier D or E.
2. What is your budget? Tiers A-B keep cost low; Tiers D-E cost significantly more in wheels, tires, and possible suspension work.
3. Is fuel economy and ride comfort a priority? If yes, stay at Tier A or B; heavier, wider wheels at Tier D-E reduce efficiency and comfort.
4. Still unsure? Tier C (Balanced / Flush Fit) is the safe default for most Skoda Rapid [RU] owners.
Offset & Backspacing Reference
Backspacing is calculated as: wheel width (in) / 2 + offset (mm) / 25.4 + 0.5.
- OE 16x6J ET38: backspacing ≈ 5"
- Flush 17x7.5J ET32: backspacing ≈ 5.51"
- Max 17x8J ET28: backspacing ≈ 5.6"
Use our offset & backspacing calculator to fine-tune your fitment, or contact ANKUSI for a custom forged wheel quote for your Skoda Rapid [RU].
Custom Forged Wheels for the Skoda Rapid [RU] (2020)
Everything above is reference data. If you want wheels actually built to it, that is what ANKUSI does: we are a forged wheel factory in Guangzhou, China, IATF 16949 and ISO 9001 certified, forging on our own 10,000-ton press and producing over 120,000 wheels a year. Forging blank, CNC machining, finishing, coating and inspection all happen in the same building — nothing is subcontracted and nothing is relabelled from another manufacturer.
Every set is cut to order, so the 5x100 pattern is machined for this car specifically. Diameter, width, offset, concavity, monoblock or multi-piece construction and the finish are all yours to choose.
Designs we already tool for the 5x100 pattern — each one is re-cut to your sizes and offsets:
Skoda OEM-Style Gloss Black Machined Face Forged Wheels – Skoda Yeti / Octavia Combi 4×4 Fitment (5-Lug)
Skoda OEM-Style Gloss Black 5 V-Spoke Machined Face Forged Wheels – Skoda Yeti / Octavia Combi 4×4 Fitment (5-Lug)
APEX VS-5RS-Style VS-5RS Light Gray 5 Y-Spoke Forged Wheels – Toyota GR86 / BMW 3 Series F30 Fitment (5-Lug)
Rays Volk Racing TE37-Style Gunmetal 6-Spoke Machined Lip Forged Wheels – Toyota GR86 / Subaru WRX Fitment (5-Lug)Frequently Asked Questions
What bolt pattern (PCD) does the Skoda Rapid [RU] use?
The 2020 Skoda Rapid [RU] uses a 5x100 bolt pattern.
How many lug bolts does the Skoda Rapid [RU] use?
The Skoda Rapid [RU] uses a 5-lug bolt pattern (5x100), so you need a 5-lug forged wheel to bolt straight on.
What does a flush wheel fitment look like on the Skoda Rapid [RU]?
For a flush look with minimal to no rubbing, we recommend 17x7.5J at ET32 offset as a starting point on a stock or mildly lowered Skoda Rapid [RU].
Do I need wheel spacers for my Skoda Rapid [RU]?
No. ANKUSI forges each wheel to your exact target offset, including the flush or max specs above, so you get the correct fitment without stacking spacers. Spacers are typically only used to push out an existing OE-offset wheel without replacing it, which isn't necessary when you're ordering a custom-offset forged wheel.
How do I calculate wheel backspacing for my Skoda Rapid [RU]?
Backspacing (in inches) = wheel width (in) ÷ 2 + offset (mm) ÷ 25.4 + 0.5 (flange allowance). For example, the flush spec above works out to roughly 5.51" of backspacing.
What's the difference between wheel offset and backspacing?
Offset is the distance in millimeters from the wheel's true centerline to its mounting face (positive offset pulls the wheel in, negative pushes it out). Backspacing is the distance in inches from the mounting face to the back edge of the wheel barrel. They describe the same fitment from two different reference points, which is why ANKUSI lists both above — some shops and tuning guides quote offset, others quote backspacing.
Can I run staggered wheels (different sizes front and rear) on my Skoda Rapid [RU]?
The Skoda Rapid [RU] runs the same wheel size front and rear from the factory, so staggered fitment is not required. ANKUSI can still forge a staggered set (wider rear) on request if you want a more aggressive stance.
Forged Wheel Designs for the Skoda Rapid [RU]
Every design below is forged to order, so it can be machined to the Skoda Rapid [RU]'s 5x100 bolt pattern, with the width and offset calculated for your setup.
Skoda OEM-Style Gloss Black 5 V-Spoke Machined Face Forged Wheels
Skoda Yeti / Octavia Combi 4×4 Fitment · 5-Lug
Toyota GR86 / Honda Civic Type R Forged Wheels
Gloss White 10-Spoke
Rays Volk Racing Metallic Gray 10 Y-Spoke Deep Lip Forged Wheels
Nissan 370Z / Toyota GR86 Fitment · 5-Lug
BBS RE-V7-Style Silver / Gloss Black 7 Y-Spoke Forged Wheels
Toyota GR86 / Honda Civic Type R Fitment · 5-Lug
BBS RE-V7-Style Metallic Gray 12-Spoke Forged Wheels
Toyota GR86 / Honda Civic Type R Fitment · 5-Lug
Rays Volk Racing Gloss Bronze Deep Lip Forged Wheels
Nissan 370Z / Toyota GR86 Fitment · 5-Lug
APEX VS-5RS-Style Brushed Silver 5 Y-Spoke Forged Wheels
Toyota GR86 / BMW 3 Series F30 Fitment · 5-Lug